Domi 2-Cam Adjustable Wing Mounting Plate, Nickel-Plated, Screw-On, 3mm

Domi 2-Cam Adjustable Mounting Plate Purpose

Domi 2-cam adjustable wing mounting plate defines this Salice America hinge mounting plate as a precise base for cabinet door hinges where accurate alignment matters. The 3mm plate height sets a consistent reference between cabinet and door, which supports repeatable reveals across a run of doors. Die-cast or stamped steel construction gives the plate a solid bearing surface for the hinge arm, which helps the hinge carry normal cabinet door loads without deforming at the connection point. Nickel plating on the steel protects the plate from corrosion in typical indoor cabinet environments, so adjustment and removal remain smooth over the life of the installation. As part of the Salice hinge system, this mounting plate works as the fixed component on the cabinet side, while the hinge arm engages on top, giving installers a stable platform to fine-tune door position using the integrated cams.

Key Mounting Plate Details That Matter

• The 3mm mounting plate height creates a known offset at the cabinet side, helping installers plan overlay and reveal consistently across matching doors on the same run of cabinetry.
• Two cam adjustment is built into the plate, giving separate cam height adjustment of plus or minus 2 mm, which lets installers raise or lower the door edge without moving screw locations.
• The additional cam depth adjustment of -0.5 mm to +2.8 mm allows the door-to-cabinet gap to be tuned from the mounting plate, which is useful for aligning doors flush on frameless cabinets or tight runs.
• Nickel-plated steel construction resists corrosion in standard cabinet environments, which preserves the integrity of the cam mechanism so future adjustments remain smooth and predictable.
• Cabinet side fastening through an open hole for #6 x 5/8 inch wood screws provides a familiar installation method, letting installers work with common screw sizes in face frame or panel materials.

Mounting And Adjustment Workflow On Cabinets

This Salice hinge mounting plate fastens to the cabinet side using an open hole sized for #6 x 5/8 inch wood screws, so it installs using standard drivers without special tools. Once fixed, the hinge arm from the selected Salice hinge series attaches to the plate, and the two built-in cams become the primary adjustment controls. The cam dedicated to height offers plus or minus 2 mm of movement, so the door can be nudged up or down relative to adjacent doors while the screws remain tight. The depth cam provides -0.5 mm to +2.8 mm of movement, which lets the door edge move in and out to refine the gap between door and cabinet, aiding in achieving clean, even lines along the cabinet face.

Using This Salice Mounting Plate In Work

Where This 3mm Plate Fits In Cabinet Runs

This hinge mounting plate belongs to the Salice America family of hinge mounting plates and is specified as 3mm, which positions the hinge arm at a defined distance from the cabinet mounting surface. That fixed 3mm build-up helps installers map overlays and hinge cup positions in design software or layout, so hinge centers and door edges align predictably from cabinet to cabinet. As a hinge mounting plate in the Hinges|Hinge Base Plates category, it serves as the interface on the cabinet side while the hinge cup is bored in the door, giving a known geometry for frameless and similar cabinet constructions. When used across a full bank of doors, the consistent plate height supports uniform joint lines, making it easier to keep reveals tight while still preserving adjustment travel in the cams for fine tuning.

Why Two-Cam Adjustment Supports Clean Alignment

The two cam adjustment built into this premium hinge mounting plate separates height and depth movements, so each alignment change can be made independently. The cam height adjustment of plus or minus 2 mm lets installers correct for small drilling variances or material tolerances by dialing the door up or down without re-drilling or loosening mounting points. The cam depth adjustment range from -0.5 mm to +2.8 mm allows the door face to be shifted closer to or farther from the cabinet side, which is particularly useful for flush-fitting modern fronts and for matching gaps between neighboring doors. This plate is compatible with Salice hinge series 100, 200, 400, F, M, Universal Hinges, and Silentia+, which means the same adjustment approach can be used across multiple hinge families in a shop that standardizes on Salice. Die-cast or stamped steel construction with nickel plating supports these fine mechanical movements by giving the cams a stable, corrosion-resistant track, so calibrated adjustments stay reliable over time.

Common Questions About This Salice Mounting Plate

Selecting This Plate For Salice Hinge Jobs

This 2-cam adjustable hinge mounting plate from Salice America gives cabinet shops and installers a 3mm screw-on base that matches Salice hinge geometry and adjustment ranges. The combination of plus or minus 2 mm height tuning and -0.5 mm to +2.8 mm depth tuning from the cams supports accurate alignment work without altering screw locations. Nickel-plated stamped or die-cast steel construction provides a stable, corrosion-resistant platform for the hinge arm in typical cabinet environments. For projects built around Salice series 100, 200, 400, F, M, Universal Hinges, or Silentia+, this plate offers a consistent way to mount and fine-tune doors across multiple cabinet runs.