Domi 2-Cam Mounting Plate For Precise Hinges
Domi 2-Cam adjustment wing mounting plate gives you a 9mm screw-on base that supports precise alignment for Salice concealed hinges. Constructed as a hinge mounting plate, it ties the hinge arm solidly to the cabinet, helping keep doors tracking correctly over time.
This Salice America hinge mounting plate is made from stamped steel or die-cast steel with a nickel-plated finish, so the plate resists corrosion in normal cabinet environments while maintaining a clean, professional look inside the casework.
The plate belongs to the Salice Domi family of two cam adjustable hinge mounting plates, so it provides an adjustment interface between the cabinet and the hinge that supports repeatable alignment during new installs or hardware changes.
The 9mm plate height establishes the door reveal geometry for the cabinet run, giving you a known starting point when pairing with the specified Salice hinge series and drilling patterns in your shop or on site.
Adjustment And Material Details That Save Time
- Two cam adjustment provides height and depth tuning at the plate, so you can bring doors into alignment using a screwdriver instead of redrilling or shifting the cabinet layout.
- Cam height adjustment range of plus or minus 2 mm lets you nudge the door up or down on the cabinet face, which is especially useful when lining up reveals across a bank of doors.
- Cam depth adjustment from -0.5 mm to +2.8 mm changes how far the door sits relative to the cabinet front, helping you fine-tune door overlay or in-out positioning without disturbing the hinge arm position.
- Nickel-plated surface over stamped steel or die-cast steel offers corrosion resistance, supporting long-term function in typical kitchen, bath, and casework environments where humidity and handling can be a factor.
- Open hole for #6 x 5/8 inch wood screws on the cabinet side allows straightforward screw-on fastening to typical cabinet materials, giving installers a familiar method for securing the plate.
Screw-On Mounting Plate Setup And Fit
This screw-on 9mm hinge mounting plate fastens to the cabinet side through an open hole sized for #6 x 5/8 inch wood screws, giving you a standard screw-driven installation method familiar to cabinet builders and installers.
The 9mm plate height establishes the working distance between the cabinet side and the hinge arm, so your layout and drilling patterns can be set up to match the geometry expected by the compatible Salice hinge series.
With its two cam design built into the plate, this BAR3R99 model lets you adjust both height and depth at the cabinet interface, which can simplify fine-tuning when multiple doors share the same run and must align cleanly.
Where This Salice Mounting Plate Excels
Using The Plate With Salice Hinge Series
This Salice America Domi 2-Cam adjustment wing mounting plate is designed for use with hinge series 100, 200, 400, F, M, Universal Hinges, and Silentia+, so a single plate style can support a wide range of Salice concealed hinge applications across your projects.
By matching this 9mm plate with those Salice hinge series, you maintain a coordinated system where the plate height, hinge geometry, and adjustment cams are engineered to work together, which supports consistent overlay and door motion across cabinets.
As a hinge mounting plate in the Domi family, the BAR3R99 part number identifies a die-cast or stamped steel plate with the two cam structure, giving specifiers and shop personnel a clear reference when ordering or repeating a cabinet hardware schedule.
Because this plate is classified under hinge mounting plates and hinge base plates, it fits naturally into standard hardware lists for casework, helping shops keep SKUs organized when planning material pulls for production runs or installations.
Adjustment Range That Supports Clean Reveals
The two cam adjustable hinge mounting design provides a cam height adjustment of plus or minus 2 mm, so you can correct small variations in drilling or cabinet construction by dialing the door position rather than altering the cabinet.
The same cam system delivers a cam depth adjustment range from -0.5 mm to +2.8 mm, letting you shift the door in or out relative to the cabinet face, which is helpful when achieving a flush look across adjoining cabinets or panels.
Since adjustment is concentrated at the mounting plate, you gain a predictable point of tuning during installation or service work, which can reduce rework time when matching reveals across multiple doors or correcting seasonal movement.
The nickel-plated steel construction supports this repeated adjustment by resisting corrosion and wear around the cam and screw areas, so the adjustment points are better able to function smoothly during typical cabinet lifespan and service events.
Common Questions About This Salice Mounting Plate
What type of product is the BAR3R99 part?
The BAR3R99 part is a Salice America Domi 2-Cam adjustment wing hinge mounting plate, so it serves as the base that connects compatible Salice hinge arms to the cabinet side.
Which Salice hinge series work with this plate?
This hinge mounting plate is for Salice hinge series 100, 200, 400, F, M, Universal Hinges, and Silentia+, allowing one plate style to cover multiple concealed hinge lines.
What adjustment range does the two cam system provide?
The two cam adjustment gives cam height adjustment of plus or minus 2 mm and cam depth adjustment from -0.5 mm to +2.8 mm, which helps bring cabinet doors into clean alignment.
How does the 9mm plate height affect door fit?
The 9mm plate height sets the baseline distance between cabinet side and hinge arm, shaping the door overlay and reveal geometry expected by the compatible Salice hinge series.
How is this hinge mounting plate fastened to the cabinet?
The mounting plate uses an open hole sized for #6 x 5/8 inch wood screws on the cabinet side, giving a standard screw-on installation approach for casework.
What material and finish does this Salice plate use?
The plate is constructed from stamped steel or die-cast steel with nickel plating, providing strength with corrosion resistance for typical cabinet and casework environments.
Select This Plate For Salice Hinge Projects
The Domi 2-Cam adjustment wing mounting plate from Salice America delivers a 9mm screw-on hinge base with defined height and depth adjustment, helping installers and shops fine-tune door alignment across cabinet runs using compatible Salice hinge series.
By using this nickel-plated stamped or die-cast steel hinge mounting plate with series 100, 200, 400, F, M, Universal Hinges, or Silentia+, you keep hardware consistent while gaining practical cam adjustments at the cabinet interface.
