Pro Value Series appliance pull gives you a 12 inch center to center grip span, which sets consistent handle spacing on tall doors or panels where alignment with other hardware matters visually across the run. The pull is part of an Appliance Pulls collection, so its scale suits full-size appliance fronts and larger cabinet applications where smaller pulls would look undersized in proportion to the panel width. A zinc die cast construction provides a solid metal body, which supports a firm hand feel on heavy use doors in busy kitchen or work areas. The oil rubbed bronze finish establishes a dark, traditional look that coordinates with other bronze decorative hardware in the same space for a unified project. With a total length of 12-3/4 inches, the pull extends slightly beyond the mounting centers, giving a balanced overhang at each end for a finished appearance.
The 12 inch center to center mounting dimension defines the exact distance between screw holes, which guides drilling into appliance panels or cabinet doors so the pull sits straight and matches other 12 inch pulls on the same elevation. With a 2-1/2 inch projection, the pull extends out from the surface enough to clear fingers between the bar and the door, which matters when opening heavier doors where a full hand grip is preferred. The 1 inch width keeps the handle visually substantial without overpowering surrounding trim, which helps maintain balanced sightlines on wide fronts. Overall length of 12-3/4 inches sets the end-to-end footprint, which is useful when checking clearance to neighboring doors or walls around corners. Screw size is specified as 10-24 x 1-1/4 inch, which indicates the threaded connection used to secure the pull through the door or panel thickness.
This oil rubbed bronze appliance pull sits within an Appliance Pulls collection, which positions it for use on large cabinet doors, appliance fronts, or tall pantry doors where a longer handle suits the scale of the surface. The 12 inch center to center dimension supports layouts on built-in appliances or oversized doors that follow a 12 inch handle spacing standard across multiple fronts. A 12-3/4 inch overall length gives a long visual line that pairs well with extended drawer banks and tall end panels, keeping hardware proportions consistent across a run of cabinets. The 2-1/2 inch projection sets the pull out from the face of the panel, which allows a full grip when opening heavier doors that see frequent operation in kitchens or workspaces. With a 1 inch width, the pull reads as a substantial bar, matching the expectation for an appliance-scale handle on wide or tall installations.
The 12 inch center to center spacing provides a fixed reference that simplifies jig setup, so hole locations repeat accurately across multiple doors using the same pull. Overall length of 12-3/4 inches makes it straightforward to center the pull visually on a panel by measuring equal overhang at each end, which helps keep hardware aligned with adjacent units. A projection of 2-1/2 inches defines how far the handle extends into the room, which aids layout decisions near corners or walkways where clearance is a factor. The 1 inch width helps installers and builders coordinate this pull with other Pro Value Series cabinet hardware pieces that share similar visual mass, supporting uniform sightlines on large installations. Zinc die cast construction gives the handle a metal body that responds predictably when tightening the specified 10-24 x 1-1/4 inch screws, which helps achieve a snug fit against the door surface. The oil rubbed bronze finish provides a dark bronze appearance that stays consistent across pulls from the same line, supporting tight visual alignment on doors, drawer fronts, and appliance panels throughout the project.
The appliance pull has a 12 inch center to center measurement, so screw holes are drilled 12 inches apart, which standardizes layout with other 12 inch pulls on the job.
The Pro Value Series appliance pull measures 12-3/4 inches in overall length, which gives slight overhang beyond the 12 inch centers for a balanced look on wide panels.
This appliance pull is made from zinc die cast, providing a solid metal body that supports repeated use on frequently opened doors and appliance fronts.
The appliance pull projects 2-1/2 inches from the surface, giving space to wrap fingers behind the bar when pulling heavier doors or tall pantry fronts.
The pull has an oil rubbed bronze finish, providing a dark bronze appearance that coordinates with other oil rubbed bronze decorative hardware on the same installation.
This appliance pull uses 10-24 x 1-1/4 inch screws, so the connection is a 10-24 machine thread passing through the door or panel into the pull body.
The 12 inch center to center layout, 12-3/4 inch overall length, and 2-1/2 inch projection position this Pro Value Series appliance pull as a practical choice where longer hardware is needed on tall doors or appliance fronts. Zinc die cast construction and a 1 inch width create a substantial metal grip that suits heavy-use kitchen or workroom fronts. The oil rubbed bronze finish ties into bronze decorative schemes, aligning this pull with other oil rubbed bronze cabinet hardware on the same job. For projects calling for a 12 inch appliance pull with defined dimensions and an oil rubbed bronze look, this SZAPPL4-ORB model matches those requirements.
Sold In: 1 Each
