Stylus Series, Zinc Die Cast Recess Pulls 1-1/2" Bore Dia., Brushed Nickel Finish

Stylus Series Recess Pull For Clean Cabinet Access

Stylus Series recess pull from Berenson Corporation is a zinc die cast recess pull in a brushed nickel finish that provides a contemporary, low-profile grip for cabinet and furniture applications where a flush look is important. The 1-1/2 inch bore diameter sets a consistent cutout size, so routing or boring can be standardized across doors and drawers on the job. Overall dimensions of 39x39mm help this pull cover a compact footprint, which suits smaller fronts or tight layouts where space is limited. The brushed nickel finish delivers a muted metallic look that pairs well with many laminates and wood tones in shop-built cabinetry. Material construction in zinc die cast gives a solid-feeling pull point, supporting repeated daily use in residential or light commercial environments while keeping the component compact.

Key Stylus Series Details For Cabinet Projects

• The 1-1/2 inch bore diameter recess pull design allows precise hole sizing, which helps jigs and boring patterns line up consistently across multiple fronts during production runs.
• The 39x39mm overall size creates a small, square footprint, which fits narrow rails or drawer faces and supports layout flexibility when hardware spacing is tight.
• The 11mm depth specification defines how deep the recess pocket must be, which helps set router bit depth for a flush fit with surrounding surfaces.
• The 1/2 inch projection indicates a shallow stand-off from the front, which keeps the pull low profile while still providing enough edge to grab during everyday operation.
• The 1-3/8 inch base dimension provides a defined bearing surface, which helps the pull sit stable in the recess and distribute hand force around the cutout edges.
• The brushed nickel finish on zinc die cast material offers a consistent surface appearance, which supports visual alignment with other brushed nickel hardware in the same space.

Recess Pull Fit, Cutout, And Mounting Considerations

The Stylus Series recess pull uses a 1-1/2 inch bore diameter, so the cutout is sized for the pull body rather than needing oversized openings, supporting a snug fit and cleaner edges after boring. An 11mm depth specification means the recess pocket must be cut to that depth, which keeps the front face of the pull aligned with the cabinet surface when installed. A 1/2 inch projection from the surface defines how far the grip stands proud, balancing a recessed look with a usable finger purchase. The square 39x39mm layout simplifies positioning because edges can reference rail or stile lines, helping installers maintain straight alignment across a row of doors or drawers. The 1-3/8 inch base dimension establishes how the pull seats in the recess, contributing to a stable, rattle-free feel when the cabinet is opened and closed.

Using This Brushed Nickel Recess Pull On Projects

Where The Stylus Series Recess Pull Works Well

The Stylus Series recess pull, with its 39x39mm size and 1-1/2 inch bore diameter, works well on cabinet doors and drawer fronts where a compact, modern pull is preferred. The brushed nickel finish supports use in kitchens, bathrooms, or casework that already uses brushed nickel hinges or handles, keeping hardware appearance consistent. The 11mm depth allows this pull to sit recessed into the panel rather than standing fully proud, which suits applications where hardware should not snag clothing or extend far into walk paths. The zinc die cast construction provides a solid pull point in everyday cabinet use, making it suitable for built-ins, shop fixtures, or furniture pieces that see frequent opening and closing. In small-format drawers, the 39x39mm footprint keeps the hardware proportional to the face size, avoiding oversized pulls on narrow components.

Details That Support Accurate, Repeatable Installation

The specified 1-1/2 inch bore diameter on this Berenson Stylus recess pull supports accurate boring with standard-size bits, which can reduce layout time when drilling multiple fronts. The 11mm depth value gives a clear target for router or drill depth stops, helping achieve a flush or near-flush fit without trial cuts. With a 1-3/8 inch base dimension, the installer knows how much bearing surface engages the cabinet, aiding in centering the pull in the recess so the edges stay even. The 1/2 inch projection provides enough edge to grip while keeping the profile shallow, which can help doors swing past adjacent surfaces without excessive interference. The square 39x39mm overall shape simplifies setting reveals relative to rails and stiles, supporting straight sightlines across a bank of cabinetry. Using a zinc die cast body with brushed nickel finish maintains consistent geometry and surface finish from piece to piece, which benefits larger jobs that require repeated hardware alignment.

Common Questions About Stylus Series Recess Pull

Select This Recess Pull For Precise Cabinet Layouts

The Stylus Series recess pull from Berenson, offered by Wurth Baer Supply, combines a 1-1/2 inch bore diameter, 39x39mm footprint, and 11mm depth to support clean, repeatable recess work on cabinets. The zinc die cast construction and brushed nickel finish create a consistent, compact pull point across doors and drawers. When a low-profile, 1/2 inch projection pull is preferred for modern cabinetry or built-ins, this recess pull provides defined dimensions that align with jigs, boring patterns, and layout lines. Choose this 9330-1BPN-C recess pull when a square, brushed nickel hardware detail is needed to match existing decorative hardware and maintain a unified look.