Stylus Series, Zinc Die Cast Recess Pulls 29 mm Bore Dia., Brushed Nickel Finish

Stylus Recess Pull 29x29mm Brushed Nickel Use

Stylus recess pull 29x29mm brushed nickel describes a Berenson Stylus Series zinc die cast recess pull designed around a 29 mm bore diameter. This square 29 mm by 29 mm hole geometry seats into a matching recess so the pull sits low, which helps keep front surfaces clean while still giving a defined grip area. The brushed nickel finish provides a muted metallic surface that blends with many decorative hardware and molding styles in the Handles and Pulls category, which supports consistent visual flow across a project. The pull uses zinc die cast construction, giving a solid metal body that helps the pull feel substantial when used on cabinet fronts or similar applications. Its Berenson Corporation 9333-1BPN-C designation and SAP description STYLUS RECESS PULL 29X29MM BRUSHED NKL tie this part to a specific size and appearance, which supports repeat ordering for matching installations.

Key Stylus Series Pull Details For Projects

• The Stylus Series identity links this recess pull to a defined Berenson decorative hardware family, which matters when matching other handles and pulls on the same job for a coordinated look.
• Zinc die cast material creates a single-piece metal pull body, which matters when a project needs a compact part that still feels solid during repeated cabinet or drawer use.
• The brushed nickel finish delivers a soft metallic appearance, which matters when tying into brushed fixtures or hinges without the sharper reflection of polished metal surfaces.
• The 29 mm x 29 mm bore diameter sizing defines the square recess needed, which matters when boring or routing a clean opening so the pull nests properly without excess play.
• The 11 mm depth figure states how far the pull extends into the recess, which matters when balancing cavity depth with panel thickness so the pull seats fully without cutting too deep.
• The 1 inch base dimension describes the outer footprint at the surface, which matters when laying out spacing on narrow rails where hardware width is limited.
• The 1/2 inch projection value states how far the pull stands proud of the surface, which matters when planning grip clearance in tight spaces or against adjacent doors.
• The 1-1/8 inch length measurement ties to the listed base and width, which matters when aligning multiple pulls in a grid so visual spacing stays uniform.

Recess Pull Mounting And Screw Fit Details

This Berenson Stylus Series recess pull is sized for a 29 mm bore diameter, so the 29 mm x 29 mm hole becomes the primary installation reference. An 11 mm depth value lets installers match drilling or routing depth so the pull body sits correctly within the panel. The projection of 1/2 inch describes how much of the pull remains above the surface, which helps anticipate hand clearance once installed. A 1 inch base dimension and 1-1/8 inch width guide layout when space near door or drawer edges is limited. The pull is supported by M4 x 1-3/4 inch break off screws, which gives a metric thread matched to many cabinet boring patterns while allowing trimming of screw length to suit varying material thicknesses.

Using Berenson Stylus Recess Pulls In Workflows

Where This 29x29mm Stylus Pull Works Best

This Stylus Series zinc die cast recess pull fits projects using a 29 mm square bore where a compact, inset pull is preferred rather than a large projecting handle. The 29 mm x 29 mm hole specification coordinates well with panel layouts that standardize on metric boring, allowing consistent spacing across banks of doors or drawers. With an 11 mm depth into the panel, the pull body occupies a modest cavity, which suits many door and drawer fronts that have limited thickness to work with while still needing a defined finger catch. The 1 inch base and 1-1/8 inch listed dimensions keep the footprint tight, which benefits narrow stiles and rails where larger hardware would crowd edges or neighboring fronts. Its brushed nickel finish allows the pull to integrate into decorative hardware and moldings that share a similar brushed metal tone, supporting cohesive styling throughout a room.

Why These Stylus Details Support Consistent Results

The defined 29 mm bore diameter gives installers a clear boring target, which helps drilling operations produce repeatable openings for multiple pulls on a run of cabinets. Knowing the 11 mm recess depth before cutting helps control how much material is removed, which supports cleaner holes and reduces risk of penetrating through thinner panels. The 1/2 inch projection sets predictable stand-off from the face, which aids in planning clearances near adjacent doors, appliances, or walls so pulls do not interfere when fronts swing or slide. The 1 inch base dimension and 1-1/8 inch measurement allow precise layout marks when aligning lines of pulls, which supports straight visual runs along drawers or doors. Use of M4 x 1-3/4 inch break off screws means the same thread size and screw type can serve panels of different thicknesses by shortening to length, which streamlines installation when cabinet materials vary across a project.

Common Questions About Berenson 9333-1BPN-C Pulls

Selecting This Stylus Pull For Your Next Job

The Stylus Series zinc die cast recess pull 29 mm bore dia., brushed nickel finish, offers a defined combination of 29 mm x 29 mm hole sizing, 11 mm depth, and 1/2 inch projection. These fixed measurements let hardware installers and serious DIY users plan boring, recess depth, and clearance around doors or drawers with confidence. With a 1 inch base footprint, 1-1/8 inch listed dimension, and M4 x 1-3/4 inch break off screws, this Berenson Corporation 9333-1BPN-C pull fits workflows built around precise layouts and metric-thread hardware. For projects running Berenson decorative hardware and moldings, this Stylus recess pull gives a clearly specified option when a compact brushed nickel pull is required.