Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO aluminum architectural pull gives you a 2 inch center to center grip in a compact 3 inch overall length, so it suits smaller cabinet fronts where standard pulls feel oversized. The anodized satin clear aluminum finish provides a neutral, low-sheen look that works with a wide range of cabinet and fixture finishes in the shop or on site. Aluminum construction keeps the pull light while resisting corrosion in typical interior woodworking environments, which supports consistent appearance across a run of cabinets. The DP Series design from EPCO identifies this pull as part of a coordinated aluminum architectural collection, helping maintain a unified hardware look across doors and drawers. A projection of 1/2 inch creates a shallow stand-off from the surface, which helps when working on tight clearances near walls, adjacent doors, or overlapping trim details.
The 2 inch center to center specification defines the spacing between mounting points, which lets installers match this EPCO aluminum architectural pull to drilled holes laid out on a 2 inch pattern. The 3 inch overall length gives a small amount of overhang beyond the mounting points, which simplifies visual alignment on rail-and-stile doors when centering the pull. A projection of 1/2 inch means the pull stays close to the face, which can be important when hardware is near appliance fronts or adjacent doors where clearance is limited. The identified screw size of 6 x 1/2 inch provides the threading and length reference, which guides drilling depth and hole sizing in typical cabinet stock during installation.
This EPCO DP Series aluminum architectural pull is categorized as a handle and pull for decorative hardware and moldings, so it is suited to cabinet doors and drawer fronts in woodworking projects. The 3 inch length allows it to sit neatly on smaller drawer faces or narrow door rails, helping maintain balanced spacing in compact layouts. With a width of 1-9/16 inch, the pull presents a solid visual bar across the surface, which supports clear hardware definition even on textured or patterned materials. The satin clear anodized aluminum finish keeps the color tone neutral, which allows the same pull to be used across mixed-material installations such as painted cabinets and wood veneers without visual conflict.
The defined 2 inch center to center dimension is the critical measurement for layout, because it aligns to hole drilling and any shop-made jigs based on that spacing. Installers can repeat the same 2 inch pattern across a bank of drawers, reducing layout time and helping maintain straight lines. The 1/2 inch projection keeps the hand contact point close to the surface, which limits interference with nearby doors or wall panels when doors swing open. The 1-9/16 inch width gives enough face for fingers to grab the pull from different angles, which supports practical use on both vertical doors and horizontal drawers. The EPCO DP41-A-3 designation ties all of these dimensions and the satin clear anodized finish to a single part number, which simplifies reorders or matching during later cabinet additions.
The EPCO DP41-A-3 pull has a 2 inch center to center, a 3 inch overall length, a 1/2 inch projection, and a 1-9/16 inch width, which together define its footprint and hand clearance on cabinets.
The 2 inch center to center spacing sets the hole pattern for the EPCO DP Series pull, which supports repeatable drilling on multiple doors and drawers using consistent jigs or measurements.
The pull uses a satin clear anodized aluminum finish, which provides a low-sheen, neutral metallic look that coordinates with many cabinet finishes and maintains an architectural appearance.
The EPCO DP41-A-3 is categorized under decorative hardware handles and pulls, so it is used on cabinet doors and drawer fronts in woodworking and cabinet projects.
The pull projects 1/2 inch from the mounting surface, which keeps it close to the cabinet face while still leaving enough space for fingers to grip during normal use.
The DP41-A-3 cabinet pull is made from aluminum, which provides a light, rigid body suitable for repeated use on cabinet doors and drawers.
This EPCO aluminum architectural pull combines a 2 inch center to center layout, 3 inch length, and 1/2 inch projection to support compact cabinet designs. The satin clear anodized aluminum finish and 1-9/16 inch width deliver a clean, defined grip line across doors and drawers. With its DP41-A-3 designation and aluminum construction, this pull provides a consistent hardware choice when planning or expanding cabinet runs that call for a neutral, architectural handle profile.
Sold In: 1 Each
