Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO DP Series aluminum pull gives a compact 1-7/8 inch center to center grip that suits small doors or drawers where space is tight, so layout stays clean even on narrow cabinet faces. The pull uses anodized satin clear aluminum, which provides a consistent aluminum finish that works well across modern or traditional shop-built runs. The aluminum material keeps the pull light while still giving a solid feel, which helps doors and drawers operate smoothly in everyday use. Overall length of 3-7/8 inch gives enough hand contact area without crowding adjacent hardware, which is useful on banks of drawers. A projection of 15/16 inch stands the pull off the face just enough for good finger clearance, helping users grab it easily without scraping knuckles against the surface. Width of 13/16 inch presents a slim profile, so the pull reads visually light while still being comfortable to grasp in routine cabinet operation.
The 1-7/8 inch center to center measurement defines the distance between mounting points, so drilling jigs or templates can be set up once and repeated across doors and drawers. With a 3-7/8 inch overall length, the pull leaves margin at each end beyond the holes, which helps position it neatly away from cabinet edges and other hardware. A 15/16 inch projection determines how far the pull sits off the face, so the handle clears door reveals while still feeling close to the cabinet for a controlled pull motion. The 13/16 inch width affects where the pull can sit relative to rail and stile details, allowing it to land comfortably on narrow framing. The DP414-A identifier ties all of these dimensions to a single EPCO pattern, which keeps field layouts consistent whenever this same pull is specified again.
This aluminum architectural pull, identified as EPCO DP Series and part DP414-A, fits well on cabinet doors and drawers that call for a compact handle pattern. The 1-7/8 inch center to center dimension works on smaller fronts where longer spreads would crowd stile or panel details, so it suits tight kitchen bases, upper cabinets, or shop casework. With an overall length of 3-7/8 inch, the pull occupies modest space on the face, which helps maintain a balanced look along banks of drawers or rows of doors. The anodized satin clear aluminum finish matches aluminum-focused design schemes, so it coordinates with other aluminum elements on workstations, office furniture, or contemporary residential cabinetry. Because the pull maintains a width of 13/16 inch, it lands neatly on face frames or slab fronts without overhanging narrow rails, which helps keep the installation visually aligned with cabinet proportions.
The fixed 1-7/8 inch center to center dimension supports repeatable drilling because once a jig is set to that spacing, the same pattern can be transferred across every front in the run, saving layout time. The 3-7/8 inch overall length allows flexible left-right positioning on doors and drawers while keeping the mounting holes inside edge clearances, which helps avoid conflicts with hinges or adjacent pulls. Projection of 15/16 inch defines a consistent standoff that gives predictable finger clearance, so users experience the same grip depth across the entire installation. The 13/16 inch width keeps the handle centered on narrow stiles without extending into panel areas, which can reduce the need for custom offsets. The anodized satin clear aluminum finish creates a uniform surface appearance, so when multiple DP414-A pulls are used, the bank of cabinets reads as a continuous, coordinated set of handles.
The EPCO DP414-A pull has a 1-7/8 inch center to center dimension, which sets consistent hole spacing for doors and drawers and supports straightforward jig-based drilling.
The EPCO DP Series DP414-A aluminum pull has an overall length of 3-7/8 inch, giving a compact footprint that suits smaller cabinet fronts while still providing a usable gripping area.
The DP414-A aluminum architectural pull has a projection of 15/16 inch, which positions the handle off the cabinet face for comfortable finger clearance during everyday use.
The DP414-A cabinet pull has a width of 13/16 inch, giving a slim profile that sits neatly on narrow rails while remaining comfortable to grasp.
The EPCO DP414-A pull uses aluminum material with an anodized satin clear aluminum finish, which delivers a consistent aluminum appearance across multiple installed pulls.
The DP414-A part number identifies this exact EPCO DP Series aluminum pull, allowing the same model to be specified again for additions or matching future cabinetry.
The EPCO DP Series DP414-A aluminum pull combines a 1-7/8 inch center to center layout with a 3-7/8 inch overall length, so cabinet runs stay visually consistent even on smaller fronts. Anodized satin clear aluminum finish coordinates easily with other aluminum elements, simplifying design choices. With a projection of 15/16 inch and width of 13/16 inch, the pull offers practical finger clearance while keeping a slim look on doors and drawers. For projects that call for repeatable, compact aluminum pulls with defined dimensions, selecting this DP414-A model supports clean, uniform cabinet installations.
Sold In: 1 Each
