Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
EPCO DP Series aluminum pull gives you a continuous 72 inch handle length in anodized satin clear aluminum, so long cabinet or door runs can be operated from end to end without breaks in the grip. The 6 foot overall length aligns with commercial-size doors or wide architectural panels where a short handle would feel undersized. The aluminum material keeps the pull light while still providing a solid feel when opening and closing large fronts. A satin clear anodized finish controls surface sheen, which supports a consistent look across contemporary or architectural projects using similar anodized trims. By using a single DP40-L-A pull across the full span, you reduce visual joints along the edge and maintain one clean line for the user to grab anywhere along the door.
The DP40-L-A aluminum pull is described as 6 foot with no holes, so installers can decide exact drilling locations along the length to align with stiles, rails, or internal reinforcement. Because the projection is 1-5/8 inch, hole positioning can be chosen to balance finger clearance with structural backing in the door or cabinet face. The 1/8 inch width keeps the required edge space small, allowing the pull to sit close to the edge of narrow doors or panels where wider bars could crowd the face. The satin clear anodized aluminum material helps the pull sit visually flat against similarly finished frames, so alignment lines at the edge of the door become more prominent than the hardware itself.
This EPCO DP Series aluminum pull, at 72 inches long, suits tall cabinet doors, wardrobe fronts, or architectural panels where users need a grip anywhere along the height. The 6 foot length lets you span most standard full-height doors with a single DP40-L-A, so the handle line reads as one continuous element instead of multiple shorter pulls. With a 1/8 inch width, the pull rides close to the edge or stile without visually overpowering narrow frames, which helps maintain slim modern proportions on vertical doors. The 1-5/8 inch projection provides enough stand-off for fingers to wrap behind the bar along its entire length, supporting consistent operation whether users grab near the top, middle, or bottom of the door.
The 6 foot no-holes configuration means mounting holes are not predefined, so drilling can be located to match existing reinforcement or to align with a specific stile layout. This allows fabricators to set fastener positions that match their door construction while still using the full 72 inch DP40-L-A profile. Because the projection is fixed at 1-5/8 inch, door and jamb clearances can be planned around a known stand-off dimension, which supports repeated use of the same pull across multiple openings in a project. The slim 1/8 inch width keeps edge reveals predictable when multiple doors sit side by side, allowing designers to maintain tight gaps without a bulky handle interfering. The anodized satin clear aluminum finish helps the pull visually coordinate across a run of cabinets or doors, which keeps each installed DP Series aluminum pull reading the same from opening to opening.
The DP40-L-A 72 inch length gives a continuous 6 foot gripping surface, so users can operate tall doors or wide panels from any point along the pull.
The 1-5/8 inch projection holds the aluminum pull off the surface enough for fingers, while keeping the handle compact for door-to-jamb or cabinet clearance requirements.
The 1/8 inch width allows the pull to sit near the door or panel edge, which helps maintain slim sightlines and tight reveals on modern cabinet or door fronts.
The satin clear anodized finish gives the pull a controlled sheen, letting it coordinate with other satin anodized trims and maintain a consistent architectural look.
The EPCO DP Series aluminum pull functions as decorative hardware and a working handle, providing a visible linear grip along cabinets or doors.
The 6 foot no holes description indicates a 72 inch pull bar without pre-drilled holes, so hole locations can be set to match specific door or panel layouts.
The EPCO DP Series DP40-L-A aluminum pull combines a 72 inch length, 1-5/8 inch projection, and 1/8 inch width in satin clear anodized aluminum, so tall or wide fronts gain a continuous architectural handle. For projects needing a single, uninterrupted grip along full-height doors or large panels, this aluminum architectural pull supplies a defined, slim bar that aligns with contemporary layouts and repeated door configurations.
Sold In: 1 Each
