Fulterer 16" Full Extension Soft-Close Ball Bearing Drawer Slides, Unhanded Side Mount Zinc - 75084

Fulterer 16 Inch Soft Close Drawer Slides

Fulterer 16 inch soft close drawer slides are full extension ball bearing side mount slides, so drawers travel their full length while running on ball bearings for controlled movement in service. The soft-close function works with the ball bearing action to pull the drawer closed in a controlled way, helping drawers end travel smoothly. The side mount design positions the slide on the cabinet sides, which suits typical drawer construction where clearances are set off the side panels. Being full extension, the 16 inch length allows the drawer box to open out to expose the full interior depth, which matters when access to the entire drawer is needed on a job. These slides are unhanded, so the same slide model serves on either side, which simplifies ordering and installation planning.

Key Working Details For Drawer Slide Selection

• The 16 inch length defines the drawer depth these slides support, so drawers can be sized to that run for consistent layout in a project.
• The full extension action carries the drawer out to its full travel distance, allowing access to the back of the drawer without reaching around the front.
• The soft-close function slows and pulls the drawer into the closed position, which helps drawers settle consistently at the same stop point.
• The ball bearing construction supports the sliding movement, so the drawer rides along the bearing races through its full extension cycle.
• The side mounting orientation sets the slides on the cabinet and drawer sides, supporting a layout built around side clearances.
• The unhanded design means each slide can serve on either the left or right, which reduces separate left/right part management.
• The zinc finish provides a metal surface treatment, which keeps the slide appearance uniform along the run.
• The soft-close trigger disconnect allows the drawer to separate from the slide, which aids in removing the drawer for cabinet work.
• The 32 mm hole pattern on the slide aligns the mounting holes to that system, which supports drilling layouts built on 32 mm spacing.
• Rear mounting brackets are available for face frame applications, so these slides can be attached at the back when working with face frame cabinets.

Side Mount Soft Close Slide Mounting Details

These Fulterer side mount drawer slides use a side mounting configuration, so both the cabinet member and drawer member fasten along the sides of the opening and box. The 32 mm hole pattern on the slide ties into 32 mm system boring, which supports using line-bored cabinet sides during layout. Soft-close trigger disconnect gives a positive point where the drawer can be separated from the slide members, which helps when fitting the cabinet or working the drawer independently. Rear mounting brackets are available for face frame applications, allowing an attachment point at the rear of a face frame cabinet to support the slide. The zinc finish on the slide components presents a consistent metal appearance along the installed parts.

Using Fulterer 75084 Slides In Real Projects

Where These Side Mount Slides Are Applied

This Fulterer USA, Inc. slide with manufacturer part number 75084 is in the side mount drawer slides product class, so it serves where a side-mounted solution is specified on cabinetry and casework. The 16 inch length works in drawer designs sized to that depth, fitting standard cabinets built around that run. The ball bearing design places the moving members on bearings, so drawers travel along those paths for the full extension distance. The 32 mm hole pattern lines the fixing points up along a consistent spacing, so shop-built cases using 32 mm system construction can reference those lines during installation. Rear mounting brackets are available for face frame applications, so casework that uses face frames can tie the back of the slide into a rear support when needed on that cabinet type.

Why These Slide Details Support Repeatable Results

The full extension function on this 16 inch soft close slide allows the drawer to open the complete travel of the slide members, so access to the rear of the drawer is consistent across cabinets. Soft-close operation combines with the ball bearing action to bring the drawer closed in a controlled motion, so the final position is reached without the drawer rebounding off the front. The unhanded construction means one slide design services both sides, so replacements or additions use the same part number 75084 without side-specific variants. The soft-close trigger disconnect creates a defined point to release the drawer member from the cabinet member, so drawers can be removed and reinstalled along the same track when other work is done inside the cabinet. With rear mounting brackets available for face frame applications, the slide can be anchored at the rear in that cabinet style, helping hold alignment between the front face frame and the back support. The zinc finish provides a uniform metallic appearance along the slide members, so the visible parts present a consistent look when the drawer is open.

Practical Questions About 16 Inch Fulterer Slides

Selecting These Slides For Side Mount Projects

The Fulterer 16 inch full extension soft-close ball bearing drawer slides from Wurth Baer Supply offer a side mount layout with an unhanded design, so one model serves either side in a run. The 32 mm hole pattern and soft-close trigger disconnect support accurate placement and straightforward drawer removal and reinstallation on shop-built cabinets. With rear mounting brackets available for face frame applications, these slides adapt to common cabinet constructions using side mounting. Use this slide where a 16 inch full extension soft-close ball bearing side mount solution fits the project layout.