Knape And Vogt 8505 Drawer Slide For File Use

Knape and Vogt 8505 drawer slide in this configuration is a 26 inch right hand cabinet member designed for side mount use on file drawers and similar applications. The 26 inch length lets you match deeper cabinet and file drawer depths where full extension plus extra reach is needed. The slide belongs to the side mount, ball bearing slide class, so it runs on ball bearings instead of friction surfaces, which supports smoother drawer travel under load. A hold-in feature is integrated to prevent drawer bounce back, so a closed drawer stays seated against the case front in normal use. Positive in and out stops are built into the slide, which limits over-travel beyond the designed range and protects both the slide and cabinet from overextension impact. The retainer holds 3 bearings per inch of race, supporting consistent rolling contact along the slide length.

Key Slide Details That Support Daily Use

• The over travel design allows the drawer to travel beyond full extension, helping expose file contents more completely, which improves access to folders at the rear of the drawer.
• The hold-in feature resists rebound when the drawer is pushed shut, which keeps fronts aligned and reduces the chance of a drawer drifting open in regular service.
• Factory-attached drawer release clips with quick disconnect drawer members speed change-out, because the drawer can be released at the clips and removed without dismantling the cabinet member.
• Progressive movement on ball bearings sequences the slide segments automatically, so the drawer opens in a single smooth motion that feels controlled from closed to full over travel.
• The retainer holding 3 bearings per inch of race supports multiple contact points along the run, which spreads loads and helps maintain smooth, quiet motion over the full travel.
• The side mount, ball bearing configuration supports lateral guidance along the cabinet side, helping keep tall file drawers tracking squarely in their openings during repeated operation.

Mounting And Clearance Details For Installation

This right hand cabinet member is part of the Knape and Vogt Model 8505 system and is intended for side mounting. The specified side clearance is 1/2 inch plus 1/32 inch, minus 0 inch on each side, so cabinet and drawer widths can be set to that clearance for proper slide engagement. The height is 3-51/64 inch including the quick disconnect rail, which helps installers gauge vertical space requirements along the cabinet side. A 32 mm pattern is present, aligning with systems that use 32 mm line boring, which can streamline layout on case sides drilled to that standard. The recommended fasteners are #7 x 5/8 inch Phillips pan head screws (BST5/8-7-2C), so the slide hole sizing and thickness are matched to that screw diameter and length for secure attachment.

Using This Right Hand Cabinet Member In Work

Where This 26 Inch Slide Fits Best

This Knape and Vogt right hand cabinet member is specified for 26 inch length applications, aligning with deeper cabinet constructions where full-depth file storage is required. As a side mount drawer slide within the 8505 series, it pairs with matching drawer members and mounting rails in that system so the complete slide set shares dimensions and patterns. The side clearance of 1/2 inch plus 1/32 inch, minus 0 inch each side means it suits case and drawer combinations built around that standard offset, which is common in many shop and commercial casework layouts. The presence of a 32 mm pattern on the slide makes it suitable for cabinet sides drilled on 32 mm centers, supporting integration into system-built casework that uses line-bored panels. The anochrome finish on the slide provides a uniform metallic appearance that coordinates with typical commercial drawer interiors and hardware lines.

Details That Support Smooth, Repeatable Operation

The factory-attached drawer release clips with quick disconnect drawer members on the 8505 series give installers and service technicians a predictable removal point, so drawers can be taken out or reinstalled at the same interface every time. The over travel motion allows drawers to extend past the cabinet front, which brings the rear of file drawers farther into reach and helps reduce bending or reaching during document handling. The hold-in feature that prevents bounce back works together with the positive in and out stops, so the slide defines both the fully closed and extended positions without relying on incidental contact between drawer parts. Progressive movement on ball bearings coordinates the sliding members so they extend in sequence, which avoids the stepped feel of non-progressive slides and supports a smoother path when users open heavy drawers. With the retainer holding 3 bearings per inch of race, the ball bearings are distributed at close intervals along the slide, supporting even load transfer and quiet running over the entire travel.

Buyer Questions About This 8505 Series Slide

Select This 26 Inch Member For 8505 Jobs

This Knape and Vogt 26 inch right hand cabinet member with over travel, hold-in, and progressive ball bearing movement provides a defined set of dimensions and mounting details. When a project calls for a 1/2 inch plus 1/32 inch side clearance, 3-51/64 inch height member within the 8505 series, this part number 8505-98 26 aligns with those requirements. Choosing this specific anochrome, side mount cabinet member keeps file drawers operating on matched components with factory-attached release clips, which supports straightforward installation and consistent drawer performance across a run of casework.