Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Knape and Vogt 14 inch over travel file drawer slide 8505-99 14 is a left hand cabinet member from the KV 8505 series that supports side mount file drawers using a ball bearing design for controlled movement in demanding cabinet applications. The over travel design allows the file drawer to extend beyond the cabinet front, giving better access to file contents without changing the basic cabinet opening. A hold-in anti-rebound feature keeps the drawer pulled fully closed until the user applies opening force, which limits bounce back in typical office or shop use. Progressive movement on ball bearings carries the load smoothly along the race, which helps drawers feel consistent through the full extension. A retainer that holds 3 bearings per inch of race supports stable, quiet motion, which matters when multiple file drawers operate in the same run of cabinetry.
This 8505-99 14 cabinet member belongs to the Knape and Vogt side mount, ball bearing slide class, so it is intended to mount along the cabinet side rather than under the drawer. The specified side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side sets a precise space between the drawer and the cabinet, which is important for these ball bearings to run without binding. A height of 3-51/64 inch including the quick disconnect rail defines how much vertical room the member uses along the case side, which guides where to position it relative to the drawer bottom and any face frame parts. The recommended fasteners are #7 x 5/8 inch Phillips pan head, which match the mounting holes and provide an appropriate grip length into typical cabinet materials.
This product is the left hand cabinet member for the Knape and Vogt 8505 series, so it mounts on the left cabinet wall to partner with the corresponding drawer member for that side. As part of a side mount, ball bearing slide system for file drawers, it suits cabinets that need over travel so the drawer front moves past the cabinet face for easier file access. The 14 inch length pairs with file drawers designed around that travel, which is common in shorter base or pedestal units. Because the member height is 3-51/64 inch including the quick disconnect rail, it fits well on cabinet sides where there is enough vertical run to position the slide above the drawer bottom while clearing any support rails. The 32 mm pattern on the member lines up with system holes in 32 mm casework, which lets production shops drop this part directly into their boring pattern without additional layout steps.
The hold-in feature on this 8505 series member is designed to prevent bounce back when the file drawer reaches the closed position, which helps drawers stay seated against the front in day-to-day opening and closing. A positive in and out stop is integrated, so the travel limits are set by the slide itself, which helps keep drawers from being overextended or pushed too far into the cabinet. Progressive movement on ball bearings means the ball races engage in sequence as the drawer moves, which spreads the load and maintains a consistent feel through the stroke. The retainer that holds 3 bearings per inch of race provides dense bearing support along the travel path, which contributes to smooth and quiet motion, especially in heavier file drawers. Factory attached drawer release clips and quick disconnect drawer members allow the installer to mount the cabinet members first, then hang or remove drawers by operating the clips, which supports adjustment, service, or replacement without realigning the cabinet side. The anochrome finish on this Knape and Vogt member provides a finished metal surface that matches the rest of the 8505 series, which keeps visible hardware consistent across a run of filing cabinets.
The 8505-99 14 is a Knape and Vogt 8505 series left hand cabinet member for side mount, ball bearing file drawer slides, so it works as the cabinet-side component in that system.
The 8505-99 14 member is 14 inches long, which suits file drawer designs built around 14 inch travel in base cabinets or pedestal units using the KV 8505 system.
The 8505-99 14 requires side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side, guiding drawer box width so the ball bearing action runs smoothly.
The 8505-99 14 has a height of 3-51/64 inch including the quick disconnect rail, which defines the vertical space it occupies along the cabinet side.
The recommended fasteners for the 8505-99 14 are #7 x 5/8 inch Phillips pan head screws, matching the mounting holes and typical cabinet side thicknesses.
The 8505-99 14 uses an anochrome finish and a 32 mm pattern, aligning with common cabinet hardware finishes and 32 mm system boring layouts.
The 8505-99 14 left hand cabinet member from Knape and Vogt combines over travel, hold-in anti-rebound action, progressive ball bearing movement, and a defined 1/2 inch plus 1/32 inch minus 0 inch side clearance to support precise, smooth file drawer motion. When a project calls for a 14 inch, side mount ball bearing file drawer slide with 32 mm pattern holes, this anochrome-finished KV 8505 member lines up with that requirement so the cabinet side can be built and bored to the stated dimensions.
Sold In: 10 Each
Quantity | Unit Price | Catalog | ||||
|---|---|---|---|---|---|---|
Sold in: 540 Each |  KV8500-92-14 Mfr# 8500-92 14 | KV8500 14" Full Extension Hold-in anti-rebound Ball Bearing Drawer Slides, Unhanded Side Mount Zinc Bulk-Pack - 8500-92 14 |
