Knape And Vogt 22 Inch Over Travel Drawer Slide Use

Knape and Vogt 22 inch over travel drawer slide describes this 8505 Series left hand cabinet member built for file drawer applications where smooth extension matters. The 22 inch length supports file drawer depths around that size, helping installers match standard cabinet layouts. This cabinet member is part of the 8505-99 22 model, so it fits into the broader KV 8505 system on corresponding drawers. Side mount design places the member on the cabinet side, which suits typical file cabinet construction where center-mount is not desired. The component is described as LH CABT MEMBER,OVERTRAVL 22, identifying it as the left hand cabinet-side piece used with a right hand counterpart. Being a specific 8505 Series part helps shops standardize on one slide family across multiple drawer runs.

Key 8505 Series Slide Details For Installers

• KV Model #8505 labeling ties this member to the Knape and Vogt 8505 Series, so shops can match cabinet members and drawer members from the same system for predictable motion.
• 22 inch length allows this cabinet member to serve file drawers built near that depth, which simplifies planning cabinet side panel dimensions and clearances.
• Side clearance of 1/2 inch plus 1/32 inch minus 0 inch on each side gives a defined drawer box width target, which supports consistent sizing across multiple drawers in a bank.
• Height of 3-51/64 inch including quick disconnect rail establishes the minimum interior cabinet height needed at the slide location, helping avoid interference with stretcher rails.
• The 32 mm pattern is present, which aligns with system line boring layouts in casework construction, so drilling operations can be coordinated with standard 32 mm rows.
• Anochrome finish on the slide provides a finished surface on the steel, which helps the component blend with other zinc-toned hardware in commercial and shop environments.

Side Mount And Over Travel Installation Details

This 22 inch side mount drawer slide cabinet member works on the cabinet wall, so it follows the normal side mount workflow of fastening through the body into the case side. The specified 1/2 inch plus 1/32 inch minus 0 inch clearance per side means drawer box widths can be set to a clear measurement target without trial fitting. The height of 3-51/64 inch including the quick disconnect rail affects where installers place rails and stretchers in the cabinet, allowing them to keep the slide clearing internal framing. The 32 mm pattern gives alignment points in system-bored cabinets, which supports faster screw placement during production runs. With the 8505 Series design, this cabinet member works as part of a progressive movement ball bearing slide set, so when paired with its matching components the drawer travel follows that engineered path.

Where This 8505 Drawer Slide Member Fits

Left Hand Cabinet Member For File Drawer Use

The LH CABT MEMBER,OVERTRAVL 22 designation identifies this piece as the left hand cabinet member in the Knape and Vogt 8505 Series system, which places it on the left interior side of the cabinet. Being part of a side mount drawer slide class means it supports drawers that hang from both cabinet walls rather than from the center. The 22 inch length aligns with deeper file drawers, so it suits casework built for letter or legal file storage where full-depth extension is needed. Over travel functionality is referenced in the name, which means when used with the proper 8505 components the drawer can extend past the cabinet face to expose file folders more fully.

The web description states this is a ball bearing slide with progressive movement, so the ball retainers support the drawer as it transitions from closed to fully extended. Positive in and out stops are part of the design, which help control the end points of travel and keep the drawer from pulling apart during normal operation. A retainer that holds 3 bearings per inch of race is mentioned, which distributes load across multiple contact points for smoother feel. The made in USA reference for KV Model #8505 matters for shops that standardize sourcing, and the anochrome finish gives a consistent metallic appearance that coordinates with other Knape and Vogt hardware in the same project.

Motion, Hold-In Function, And Quick Disconnect Value

The description notes factory-attached drawer release clips with quick disconnect drawer members, which means the system is designed so the drawer member can be released from the cabinet member without removing separate clip hardware. In use, this helps when casework needs finishing or service away from the installed cabinet, because the drawer box can be separated from the cabinet-mounted members. The hold-in feature to prevent bounce back is part of the 8505 design, so when the drawer is closed the mechanism helps resist the drawer rolling forward again under vibration or minor disturbances.

Progressive movement on ball bearings is highlighted, which indicates the slide sections move in sequence as the drawer opens, giving a controlled extension. Positive in and out stops add defined endpoints to that motion, helping keep the drawer within its intended travel distance. The 3 bearings per inch of race detail shows that each inch of the slide raceway carries multiple ball bearings, supporting smoother and quieter motion as described. Recommended fasteners are specified as #7 x 5/8 inch Phillips pan head screws (BST5/8-7-2C), giving installers a known shank and head combination that suits the mounting holes. When this left hand cabinet member is paired with its right hand mate and the proper drawer members, the result is a file drawer slide system tuned for repeatable motion and manageable removal.

Common Questions About This 22 Inch KV Slide

Selecting This 8505 Member For File Drawers

The Knape and Vogt 22 inch over travel drawer slide cabinet member offers a defined 1/2 inch plus 1/32 inch minus 0 inch side clearance, progressive ball bearing movement, and a 32 mm pattern that fits system-bored casework. For file drawer projects built around the 8505 Series, this left hand cabinet member helps standardize motion, layout, and drilling. Add it to designs where controlled extension, hold-in at close, and quick disconnect capability support everyday use and shop workflow.