Salice Excentra S 3 cam hinge is a concealed cabinet hinge from Salice America designed for face frame cabinets needing a 1-5/16 inch overlay and self-closing action. This Series S face frame hinge is specified as a 106 degree screw-on hinge, so doors open to a wide, workable angle while staying inside a typical cabinet footprint. The hinge is part of the Salice Excentra face frame line, so it is built around three-cam adjustment that supports repeatable alignment. As a concealed cabinet hinge, it keeps hardware out of sight when the door is closed, which suits residential and commercial cabinetry where a clean appearance matters. The part number CSP3B99NR identifies this exact 1-5/16 inch overlay, 106 degree self-close face frame hinge with screw-on mounting and three-cam adjustability.
This Salice face frame hinge is specified for a 1-5/16 inch overlay, so the door edge covers that amount of the face frame when hung. Excentra hinges with overlays of 1/2 inch and greater have zero door protrusion, which means doors swing without projecting into the cabinet opening and stay clear of interior pullouts that operate in line with the opening. The hinge is designed to work with cabinet doors up to 3/4 inch thick, so standard kitchen and bath door thicknesses fall within its application range. A hinge cup edge drilling distance of 2.5 mm sets the bore position from the door edge, guiding boring setups for repeatable hinge cup placement across multiple doors in a run.
This Salice CSP3B99NR hinge is a 1-5/16 inch overlay face frame hinge in the concealed cabinet hinges class, so it is suited to face frame cabinetry where doors must overlay the frame by that amount. Because Excentra hinges with overlays of 1/2 inch and greater have zero door protrusion, this hardware works well on cabinets that use interior rollouts or organizers which travel straight out through the opening. The hinge is designed to work with cabinet doors up to 3/4 inch thick, aligning with common residential and light commercial door construction, so shops following standard thickness practices can stay within the hinge design envelope. A cup depth of only 11 mm allows this hinge to be used on most door styles, which supports profiles and edge treatments that leave less material for deep cup boring. The hinge cup edge drilling distance of 2.5 mm defines the setback from the door edge, which simplifies jig selection and CNC programming for consistent mounting layouts across repeated doors.
Excentra three cam adjustment hinges provide cam depth adjustment from plus 2.8 mm to minus 0.5 mm, letting the door move in and out relative to the cabinet face so reveals and flush conditions can be tuned after hanging. They also provide cam lateral adjustment from plus 3.0 mm to minus 2 mm, which is the side-to-side movement that solves butt door problems when pairs of doors meet at center. Slotted screw hole height adjustment of plus or minus 2 mm sets vertical placement, so doors can be raised or lowered within that range to level tops and bottoms across a run. This 3-cam adjustable hinge is described as providing the best side to side adjustment in the industry, giving additional working latitude when cabinet openings or doors vary slightly from drawing. All hinges in this Excentra line are self-closing design, so once alignment is dialed in, doors are pulled to the closed position reliably without relying on catches.
This hinge is a Salice Series S face frame hinge in the concealed cabinet hinges class, so it serves face frame cabinets where concealed hardware and a set overlay are required.
The hinge is specified as a 1-5/16 inch overlay face frame hinge and is designed to work with cabinet doors up to 3/4 inch thick, fitting standard overlay and thickness combinations.
The hinge is a 106 degree screw-on hinge, so it opens doors to approximately 106 degrees, giving good access to cabinet interiors while keeping the motion controlled.
Excentra three cam adjustment hinges provide depth from plus 2.8 mm to minus 0.5 mm, lateral from plus 3.0 mm to minus 2 mm, and height plus or minus 2 mm through a slotted screw hole.
A cup depth of only 11 mm allows this hinge to be used on most door styles, so thinner profiles and detailed routings still retain enough material behind the cup bore.
Salice Excentra face frame hinges have all steel one piece construction with nickel plating to resist corrosion, which protects the moving parts in typical kitchen and bath environments.
This 1-5/16 inch overlay Salice Excentra S 3 cam hinge combines concealed cabinet hinges design with three-axis cam adjustment, so it supports precise door alignment on face frame cabinets. The 106 degree self-closing action and zero door protrusion on overlays of 1/2 inch and greater keep doors moving in a controlled arc that works with interior storage. The 11 mm cup depth, 2.5 mm cup edge drilling distance, and capacity for doors up to 3/4 inch thick tie directly into standard shop boring and door-building practices. For projects built around Salice components, this hinge also works with Salice Type U soft-close devices, giving a path to add soft closing where needed.
Sold In: 1 Each
