Salice Excentra S face frame hinges are concealed cabinet hinges designed for face frame construction, so they keep the hardware hidden while controlling overlay and movement on framed cabinet jobs. These hinges provide perfect closing to any kind of door, which helps doors land consistently and stay shut in everyday use. A 1-3/8 inch overlay rating sets the hinge up for larger overlays on face frame cabinets, helping you match the overlay needed on full-face or butt door layouts. A 106 degree opening angle gives doors wide swing without overextending, which helps in tight runs where cabinets meet walls or appliances. The hinge is self-closing, so the door pulls itself shut from the last few degrees, supporting a clean close without extra catches. Nickel plating resists corrosion, so the hinges stay functional in typical kitchen and bath environments.
Salice Excentra face frame hinges are built as concealed face frame hinges, so they mount to the interior of a face frame while keeping the cup fixed in the door for a clean exterior look. A hinge cup edge drilling distance of 2.5 mm locates the cup close to the door edge, supporting typical drilling patterns used on modern cabinet doors. Cam depth adjustment from plus 2.8 mm to minus 0.5 mm lets you move the door in and out relative to the face frame, which helps flush the door plane across a run. Cam lateral adjustment from plus 3.0 mm to minus 2 mm provides side to side movement, which is particularly useful when aligning butt doors. A slotted screw hole height adjustment of plus or minus 2 mm gives vertical movement, helping fine-tune reveals at top and bottom rails.
These Salice Excentra S face frame hinges fall under concealed cabinet hinges, so they are aimed at installations where the hinge needs to be hidden on the finished face while remaining accessible for adjustments inside the cabinet. Being designed as face frame hinges, they suit framed cabinet construction where a front frame surrounds the opening and the hinge must bridge between the frame and a full overlay or large overlay door. The 1-3/8 inch overlay capability positions the door to cover much of the face frame, which works on full-overlay kitchen runs and on butt door applications where two doors meet over a shared stile. A 106 degree opening angle supports everyday access to interior storage without pushing doors into extreme swing, which fits wall and base cabinets positioned near appliances or room transitions.
This 2-cam adjustable hinge provides the best side to side adjustment in the industry to ensure butt door problems are resolved, so installers can dial in tight centerline gaps without refitting doors. Excentra, two cam adjustment hinges provide cam depth adjustment from plus 2.8 mm to minus 0.5 mm, which lets you pull doors closer to the face frame or move them outward to align with adjoining units and trim. The cam lateral adjustment from plus 3.0 mm to minus 2 mm gives generous side to side travel, so small drilling variances or door width tolerances can be corrected at the hinge rather than in the shop. A slotted screw hole height adjustment of plus or minus 2 mm allows vertical tuning, helping level door tops across long runs and balance the gap above toe kicks or countertops. Excentra face frame hinges are designed to work with Salice Type U soft-close devices, so soft-close performance can be added using the matching dampers while the hinge continues to handle positioning and overlay. All hinges are self-closing design, which means once adjusted, the closing action helps pull doors tight, reducing bounce-back and improving alignment over time.
The Salice CSR3C99N hinge is a concealed face frame hinge for face frame cabinets, so it works where a framed front needs an internal hinge connection to an overlay door.
The 1-3/8 inch overlay lets the door cover more of the face frame, which supports full-overlay and butt door layouts where doors need to meet closely over center stiles.
This face frame hinge is designed to work with cabinet doors up to 3/4 inch thick, fitting common residential cabinet door constructions without special door build-ups.
The Excentra two-cam system provides depth, lateral, and height adjustment ranges, so you can fine-tune door reveal, flushness, and butt door alignment directly at the hinge.
On overlays of 1/2 inch and greater, zero door protrusion means the open door does not project into the cabinet interior, which helps clear pull-outs and interior storage.
Excentra face frame hinges are designed to work with Salice Type U soft-close devices, allowing soft-close damping to be added while the hinge manages overlay and movement.
The Salice Excentra S face frame hinges combine a 1-3/8 inch overlay, 106 degree opening, and self-closing action, which together support clean, modern runs on framed cabinets. The 11 mm cup depth and 2.5 mm cup edge distance align with common door machining, so they drop into standard drilling patterns on most door styles. With depth, lateral, and height cam adjustments plus nickel-plated all steel one piece construction, this hinge offers the control and durability needed for busy projects. For face frame jobs where concealed hardware, generous overlay, and precise butt door adjustment are priorities, this Salice CSR3C99N hinge is a practical choice to specify and use.
Sold In: 1 Each