Amerock Concentric Finger Pull For Cabinet Projects

Amerock Concentric finger pull gives a compact, modern grip for cabinet doors and drawers using a 1-1/4 in (32 mm) center-to-center mounting layout, so it aligns with standard 32 mm drilling patterns in many cabinetry runs. The pull uses smooth curves and sharp lines to create visual depth, which helps a small piece still read as a deliberate design detail on doors and drawer fronts. Its zinc construction provides a solid metal body, so the pull feels substantial in hand during repeated use. The satin nickel finish delivers a muted metallic look that works well with many hinge and appliance finishes in the same tone family. With a length of 1-11/16 in (43 mm) and a 7/8 in (22 mm) projection, the pull stays compact while still leaving enough space behind it for a comfortable finger grip in tight layouts.

Key Amerock Concentric Finger Pull Details

• The 1-1/4 in (32 mm) center-to-center dimension sets consistent hole spacing, which simplifies drilling layouts and makes it straightforward to position multiple Amerock Concentric pulls on a bank of fronts.
• The 1-11/16 in (43 mm) overall length keeps the pull visually compact, which helps it sit comfortably on narrow drawer fronts or small doors where larger pulls could crowd rails or stiles.
• The 7/8 in (22 mm) projection defines how far the pull stands off the surface, giving fingers room to hook behind the pull without needing deep overhangs that might snag clothing.
• The 1 in (25 mm) width provides a stable front surface, spreading contact over a wider area so the pull feels controlled when opening heavier cabinet drawers or doors.
• The 5/16 in (8 mm) base length and 1 in (25 mm) base width focus contact at the mounting points, helping seat the pull firmly against the cabinet face for a clean, finished look.
• The 8-32 x 1 in screw size matches a common cabinet thread standard, which supports a familiar installation process when fastening the pull to typical cabinet door and drawer materials.

Mounting And Fit Details For This Finger Pull

The Amerock Concentric finger pull uses a 1-1/4 in (32 mm) center-to-center mounting pattern, which sets the distance between the mounting holes and guides drilling and jig placement. With a 7/8 in (22 mm) projection, the pull stands far enough off the cabinet face to give room for a fingertip grip while staying close to the surface to keep fronts reading flush. The 1 in (25 mm) width and 1-11/16 in (43 mm) length define a compact footprint, so the pull fits comfortably on smaller drawer faces and narrow rails. The zinc material creates a metal body ready to be fastened from the back side, and the 8-32 x 1 in screw size aligns with a typical cabinet hardware thread, supporting a familiar mounting approach on standard door and drawer thicknesses.

How This Satin Nickel Pull Works In Cabinets

Where The Amerock Concentric Finger Pull Fits Best

The Amerock Concentric finger pull, identified as BP36811G10, is designed as a handle and pull for cabinet applications, so it suits cabinet doors and drawer fronts in woodworking projects. Its 1-1/4 in (32 mm) center-to-center sizing ties into a common cabinet hardware standard, which helps it integrate into layouts that already use 32 mm spacing or are drilled with system jigs. With a 1-11/16 in (43 mm) length and 1 in (25 mm) width, the pull occupies a small area on the front, making it a practical option for compact drawer faces, narrow face frames, or modern slab doors where a minimal look is preferred. The satin nickel finish coordinates with other satin nickel cabinet hardware, such as hinges or other pulls in the same space, keeping visual continuity across a run of doors and drawers.

Details That Support Consistent Cabinet Installations

The 1-1/4 in (32 mm) center-to-center measurement on this Amerock Concentric finger pull drives consistent hole spacing, which helps installers repeat measurements accurately across multiple fronts. The 5/16 in (8 mm) base length and 1 in (25 mm) base width define the footprint at the contact point, giving a predictable area to reference against edge reveals or stile widths when laying out hardware. A 7/8 in (22 mm) projection sets a known stand-off distance, which matters when aligning pulls opposite hinges to avoid interference with surrounding components. The zinc construction provides a solid, uniform substrate under the satin nickel finish, keeping the tactile feel consistent from one pull to the next in larger cabinet runs. With a standardized 8-32 x 1 in screw size listed, the fastening setup stays the same from cabinet to cabinet, supporting repeatable installations on door and drawer fronts cut from similar stock thicknesses.

Common Questions About Amerock Concentric Finger Pull

Selecting This Pull For Your Next Cabinet Run

The Amerock Concentric finger pull BP36811G10 combines a 1-1/4 in (32 mm) center-to-center layout with compact overall dimensions, giving a small-format option that still follows common drilling patterns. Its zinc construction and satin nickel finish deliver a metal pull that visually coordinates with other satin nickel cabinet hardware. With a 7/8 in (22 mm) projection and 1 in (25 mm) width, the pull offers a usable grip while staying visually tight to the front. For cabinet doors and drawers laid out around 32 mm spacing, this Amerock Concentric finger pull provides a practical satin nickel choice to carry across a full run.