Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Pro Value Elite I backplate is a zinc die cast pull backplate in the Elite I collection that sits behind a handle to visually frame the pull and cover the cabinet surface in that footprint. The 3 inch center to center layout lines up with pulls that share the same hole spacing, so it supports consistent handle positioning across doors and drawers using that standard measurement. The 6-1/2 inch overall length and 1 inch width create a defined band of metal behind the pull, which helps mask previous impressions in that area when hardware is updated. The oil rubbed bronze finish presents a dark, uniform face under a matching pull, giving cabinets a coordinated look across a run. The 3/16 inch projection lifts the pull slightly away from the door or drawer face, which establishes a repeatable stand-off depth along a bank of fronts.
This zinc die cast backplate is built around a 3 inch center to center pattern, so it aligns with pulls drilled on that spacing during installation. The 6-1/2 inch overall length means the plate extends beyond the screw points, providing a larger contact patch on the door or drawer surface wherever it is mounted. With a 1 inch width, the piece stays narrow enough to sit neatly on most cabinet stile faces while still covering the immediate area around the screw line. The 3/16 inch projection keeps the hardware profile low against the cabinet, which helps maintain a close, controlled look across face frames and flat fronts. The oil rubbed bronze finish is matched on the full visible surface, so once the pull is mounted through the backplate, the exposed metal reads as a single, consistent field.
This Pro Value Series backplate belongs to the Elite I collection, so its styling and proportions are coordinated within that group of pulls and plates. The 6-1/2 inch long by 1 inch wide format suits installations where a standard 3 inch center to center pull is used, because the backplate spans beyond the screw points to frame the handle visually. On doors or drawers with existing 3 inch holes, the matching center to center layout lets this plate sit between the pull and the surface without altering that drilling pattern. The oil rubbed bronze finish supports use on cabinets where a dark, uniform metal strip behind the pull is preferred, since the plate presents that color consistently along its length. The 3/16 inch projection keeps the profile slim against both framed and frameless fronts, which helps the hardware read as a tight, controlled band rather than a bulky element.
The 3 inch center to center measurement defines the exact location of the mounting holes in the backplate, so installers can rely on that spacing when drilling or reusing holes for coordinating pulls. Because the zinc die cast plate is 6-1/2 inches long, there is metal extending past each screw location, which helps distribute the clamp load across more surface area once the pull is tightened down. The 1 inch width creates a predictable reveal around the pull base, making it easier to maintain straight sight lines when aligning multiple doors in a row. With a 3/16 inch projection, the combination of pull and backplate sits just slightly off the cabinet face, which can support a consistent hand clearance feel across the entire run of cabinetry. The oil rubbed bronze finish stays visible around the pull base, tying separate openings together visually since each pull sits on the same colored strip.
This backplate is drilled on a 3 inch center to center pattern, so it aligns with pulls that share the same 3 inch mounting hole spacing.
The Elite I Series backplate has a 6-1/2 inch length, a 1 inch width, and a 3/16 inch projection, defining the metal footprint behind the pull.
The SZELI9-ORB backplate uses zinc die cast construction, giving it a solid metal body that supports the pull across its mounting span.
This Pro Value Series backplate has an oil rubbed bronze finish, so it presents a dark, consistent metal surface behind the pull.
The backplate has a 3/16 inch projection, which sets a low profile while still lifting the pull slightly off the cabinet face.
This pull backplate is part of the Elite I collection in the Pro Value Series, so it is coordinated with that group of decorative hardware.
This Pro Value Elite I Series zinc die cast pull backplate in oil rubbed bronze pairs a 3 inch center to center layout with a 6-1/2 inch by 1 inch footprint, giving installers a defined metal field behind the pull. The 3/16 inch projection keeps the hardware profile controlled while still lifting the pull slightly away from the cabinet face. For projects using 3 inch center to center pulls in a dark finish, this SZELI9-ORB backplate offers a coordinated way to frame each handle and cover the immediate surface around the mounting points.
Sold In: 1 Each
