Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Pro Value Elite I Series pull gives cabinets a consistent look by pairing the Elite I collection design with an oil rubbed bronze finish, so new and existing fronts can match visually across a project. The pull uses zinc die cast construction, which provides a solid metal feel while keeping weight manageable when many pulls are installed on a large run of doors and drawers. A length of 4-1/8 inches spans typical cabinet rail widths, helping this pull sit proportionally on standard doors. The 1-1/8 inch projection creates finger clearance off the face of the cabinet, which supports a comfortable grip when opening heavier drawers. A width of 3/8 inch keeps the profile slim, which helps avoid interference when doors open past adjacent components in tight layouts.
The variable center-to-center distance from 3 inches to 3-3/4 inches allows this pull to tie into both 3 inch and 96 mm drilling patterns, which are common on many cabinet lines. This flexibility supports retrofit work where existing bores cannot move. With a 4-1/8 inch total length, the pull overhang on each side of the mounting holes remains modest, which helps it sit cleanly on narrower drawer fronts. The 3/8 inch width keeps edge distance reasonable from screw line to handle edge, which supports stable mounting in typical cabinet materials. A projection of 1-1/8 inches keeps the grip area far enough off the door or drawer face that knuckles clear the surface during use.
This Pro Value Series handle from the Elite I collection works wherever a decorative pull is needed on cabinet doors or drawers within its 3 inch to 3-3/4 inch center-to-center range. The oil rubbed bronze finish lets the pull coordinate with other dark-toned decorative hardware and moldings in the same space, which supports a unified look in kitchens, baths, or shop-built casework. Because the pull belongs to the Elite I collection, it can be used alongside other Elite I pieces to carry one design language across varying cabinet sizes. The 4-1/8 inch length fits comfortably on many standard-width rails, so installers can repeat the same part across uppers, bases, and utility cabinets without changing drilling setups.
The zinc die cast construction of this cabinet pull provides consistent dimensions from piece to piece, which helps jigs and drilling templates line up accurately over an entire run of cabinets. The variable center-to-center spacing, from 3 inches to 3-3/4 inches, gives flexibility when matching existing bores or planning new layouts based on either imperial or 96 mm spacing. That range lets installers keep a single pull specification even when cabinet suppliers vary their drilling standards. The 1-1/8 inch projection and 3/8 inch width repeat predictably, so alignment against doors and drawer fronts stays uniform. The specified 8-32 x 1 inch screw size defines the thread and length the pull is designed around, which allows installers to select fasteners that reach through common door and drawer thicknesses while engaging the internal threads properly.
The Pro Value Elite I Series pull fits center-to-center distances from 3 inches to 3-3/4 inches, so it works with both 3 inch and 96 mm hole layouts on cabinet doors and drawers.
The SZELI5-ORB cabinet pull measures 4-1/8 inches in overall length, so it spans a useful portion of typical drawer and door rails without overpowering narrower fronts.
The zinc die cast cabinet pull has a 1-1/8 inch projection, which sets the grip area off the surface to give fingers clearance when opening doors and drawers.
The cabinet handle has a variable center-to-center range from 3 inches to 3-3/4 inches, allowing it to line up with both imperial and 96 mm mounting patterns.
The Elite I pull is made from zinc die cast material with an oil rubbed bronze finish, which defines both its feel in hand and its dark, warm visual appearance.
This Pro Value Series handle is designed for 8-32 x 1 inch screws, so the internal threads and length expectation match common cabinet door and drawer thicknesses.
This 3 inch to 3-3/4 inch oil rubbed bronze cabinet pull combines the Elite I collection style, zinc die cast construction, and a 4-1/8 inch length, so it covers both new layouts and retrofit work using the same handle. With its defined 1-1/8 inch projection, 3/8 inch width, and 8-32 x 1 inch screw size, the pull offers clear mounting expectations that suit many standard cabinet fronts. Choose this SZELI5-ORB cabinet pull when a variable center-to-center range and a coordinated oil rubbed bronze finish are important on the job.
Sold In: 1 Each
