Pro Value Elite I cabinet pull is a 3 inch center to center handle designed for cabinet and drawer fronts where a consistent hole spacing speeds layout and drilling. The pull uses a 3 inch, or 76 mm, center to center dimension, which matches many standard boring patterns and helps keep replacement or new installs straightforward. It is built from zinc die cast material, which provides a solid, uniform body that holds threads well for an 8-32 screw connection. The satin nickel finish gives a muted metallic look that pairs with a wide range of decorative hardware and moldings without drawing glare. Overall length is 4-1/2 inches, so the grip area spans comfortably across typical cabinet rail widths. A 1 inch projection and 1/2 inch width keep the pull compact on the face while still leaving space for fingers to grab.
This 3 inch center to center pull is set up around the common 76 mm bore spacing, which lets it fit many cabinet layouts that follow that standard dimension. With a 4-1/2 inch length, the standoffs fall inboard from the ends, leaving some metal beyond the screw lines that visually caps the pull on the cabinet face. The 1 inch projection establishes a consistent stand-off from the door or drawer, which keeps fingers away from the surface while pulling. A 1/2 inch width keeps the mounting footprint relatively narrow, which can matter on face frames or narrow rails where extra room is limited.
This Elite I Series pull sits in the decorative hardware and moldings category as a handle and pull, placing it directly in typical cabinet and drawer applications. The satin nickel finish lets it work across many door styles, because the subdued sheen reads as a neutral metal against painted or stained wood. With a 4-1/2 inch length and 3 inch center to center spacing, the pull suits many kitchen and bath cabinet doors where that drilling is already planned. The 1 inch projection supports use on drawers near adjacent obstacles, because the pull does not extend excessively into the room. Zinc die cast construction contains the shape in a compact form that suits both small and medium fronts.
The 3 inch (76 mm) center to center measurement gives installers a fixed reference that can be repeated across a run of doors, which supports straight, level lines when used with a drilling jig based on that spacing. The 1/2 inch width keeps the contact strip narrow, which can be useful when aligning the pull on face frames or narrow stiles without crowding edges. A 1 inch projection provides a predictable stand-off from the surface, which aligns multiple pulls to the same depth and creates a uniform shadow line. The satin nickel finish presents a consistent tone across each piece, which helps banks of cabinets read as a coordinated installation. Zinc die cast material supports stable internal threads that pair with an 8-32 x 1 inch screw size, which ties the pull firmly to typical cabinet door and drawer thicknesses using a familiar fastener standard.
The Pro Value Elite I cabinet pull has a 3 inch center to center, 4-1/2 inch overall length, 1 inch projection, and 1/2 inch width, which defines its footprint on typical cabinet doors and drawers.
The 3 inch center to center spacing provides a common 76 mm drilling pattern, which lets installers repeat hole locations across doors and drawers using standard templates.
The Elite I Series pull is zinc die cast, which creates a solid metal body that holds 8-32 screw threads and delivers consistent edges around the handle shape.
The 1 inch projection sets the pull off the cabinet surface, giving fingers space to grip while keeping the handle from extending too far into walkways or tight areas.
The satin nickel finish offers a muted metallic look with reduced glare, helping the pull coordinate with various cabinet colors and other satin nickel decorative hardware.
The SZELI10-SN cabinet pull is threaded for 8-32 x 1 inch screws, aligning with a common cabinet hardware fastener standard for many door and drawer thicknesses.
The Pro Value Elite I cabinet pull with 3 inch center to center spacing aligns with common cabinet drilling, which supports efficient runs of doors and drawers. With its 4-1/2 inch length, 1 inch projection, and satin nickel finish, the pull fits many layout and style plans. Choosing this zinc die cast handle within the decorative hardware and moldings category helps keep dimensions, screw threading, and visual tone consistent across the project.
Sold In: 1 Each
