Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Pro Value Elite II Series 3 inch pull describes a zinc die cast cabinet handle with a satin nickel finish that spans a 3 inch center to center mounting, so it lines up with standard 3 inch drilling on many drawer fronts and doors. The pull measures 3-1/2 inch in overall length, giving a slight overhang beyond the 3 inch boring, which provides finger clearance at each end during daily use. A 1 inch projection sets the gripping surface out from the cabinet face, creating space for a comfortable grab while keeping the handle close enough to the door for a clean profile. The 1/2 inch width gives a slim look while still presenting enough surface area for a secure hand feel when opening heavier cabinet sections.
The 3 inch center to center dimension on the Pro Value Series satin nickel pull identifies the distance between mounting points, so it connects directly to fronts that already use this standard boring layout. The 3-1/2 inch overall length then slightly exceeds that spacing, which visually covers the holes while leaving a comfortable gripping span across the handle. A 1 inch projection controls how far the pull stands off the face, which affects finger access in tight clearances such as near wall returns. The 1/2 inch width defines the narrow front face, balancing a slim line appearance with enough surface to grasp even on smaller drawer fronts.
The Elite I collection cabinet handle designation places this SZELI2-SN pull within a decorative hardware family suited to cabinets and similar casework, so it works across doors and drawers that match its 3 inch boring. The 3 inch center to center measurement aligns with many existing cabinet layouts, which helps when selecting a pull that follows an established drilling pattern across a kitchen, bath, or shop bank of cabinets. Its 3-1/2 inch overall length gives slightly more bar to grab than the hole spacing alone, which is useful on medium-width fronts where extra finger room improves everyday operation. Because the projection is 1 inch, the pull stands off the surface enough to accommodate most hand sizes in front of the 1/2 inch wide face, keeping operation consistent from one opening to the next.
The 3 inch center to center cabinet pull format standardizes measurements, which simplifies layout work when repeating the Pro Value Elite II Series 3 inch pull across multiple cabinet runs. With a 3-1/2 inch length, installers can reference a known end-to-end dimension during alignment, helping to set uniform reveals from door edges. The satin nickel cabinet pull 3 inch cc finish maintains a soft metallic look, which is helpful when matching to other satin nickel decorative hardware and moldings in the same space. The zinc die cast cabinet pull construction gives a single-piece body that supports routine opening and closing without separate components along the grip. The 1 inch projection and 1/2 inch width together define a compact footprint, which can reduce interference in corners or near appliance faces where extra clearance is limited.
The Pro Value Elite II Series 3 inch pull uses 3 inch center to center spacing, so the mounting holes align on a 3 inch layout across the cabinet face.
The satin nickel cabinet pull measures 3-1/2 inch in overall length, extending slightly past the 3 inch hole spacing to provide extra gripping area.
The Elite I collection handle is made from zinc die cast, which forms a solid molded body supporting the 3 inch span between mounting points.
The pull has a 1 inch projection, setting the grip off the cabinet surface to allow finger access while keeping a low-profile appearance.
The Pro Value Series satin nickel pull has a 1/2 inch width, providing a slim look while offering enough front surface for a steady grip.
The SZELI2-SN pull uses a satin nickel finish, giving a muted metallic appearance that coordinates with other satin nickel decorative hardware.
The Pro Value Elite II Series 3 inch pull combines a 3 inch center to center drilling, 3-1/2 inch overall length, 1 inch projection, and 1/2 inch width in a zinc die cast body with a satin nickel finish. Those dimensions and materials define how it lines up with 3 inch layouts, how it feels in hand, and how it visually matches other satin nickel hardware. When a project calls for a 3 inch center to center cabinet pull from the Elite I collection, this SZELI2-SN model offers a clearly defined size and finish profile ready to match that specification.
Sold In: 1 Each
