Larsen and Shaw piano hinge in bright brass finish provides a continuous pivot for lids, doors, or panels over a 30 inch run, which helps spread load along the full length instead of at individual hinge leaves. This piano hinge is 1-1/2 inches wide when opened, giving a broad bearing surface that supports alignment of mating parts along the full edge. The hinge is made from .060 gauge steel, so the leaves and knuckle have substantial thickness for a solid feel during operation. A bright brass finish on the steel hinge adds a brass appearance over the entire length, which helps match brass-toned projects while keeping a uniform look where the hinge remains visible. As part of Larsen and Shaw's high quality piano hinge line, this 30 inch length fits projects where a standard, repeatable size is preferred.
This Larsen and Shaw piano hinge uses countersunk screw holes spaced 2 inches apart on center, which yields a regular mounting pattern that helps position fasteners evenly along the door or lid edge. All piano hinges in this line use #5 flathead screws, except 3 inch wide hinges that use #6 flathead screws, so this 1-1/2 inch width uses #5 flathead screws for mounting to the mating surfaces. The consistent screw size across non-3 inch widths helps standardize drilling and bit selection when using several widths from the same family on one project.
The 1-1/2 inch opened width positions this bright brass piano hinge for use on doors, lids, or panels that need moderate bearing area without the footprint of 2 inch or 3 inch hinges. At 30 inches long, the hinge suits mid-size cabinet doors and storage lids where a continuous hinge improves support across the full height or width. The .060 gauge steel construction allows the hinge knuckle to provide a firm pivot along these lengths, so the moving part tracks on a defined centerline instead of drifting under normal operation. Because hinge widths in the Larsen and Shaw line range from 1-1/16 inch to 3 inches, this 1-1/2 inch size sits in the middle of the range, offering a balance between compact footprint and contact area. The bright brass finish makes this hinge a match for projects where the hardware is visible and needs a brass color consistently along the entire hinge line.
The 2 inch on-center spacing of the countersunk screw holes guides a regular pattern of fasteners along both leaves, which helps installers maintain straight alignment down the edge as each screw pulls the hinge tight. Using #5 flathead screws on this 1-1/2 inch piano hinge means the screw heads sit into the countersinks, so the heads sit flush with the hinge surface and do not interfere with the mating part as it moves past the leaves. Across a 30 inch length, this consistent hole spacing and screw size support repetitive drilling and driving steps, which can speed up work when multiple hinges are mounted in the same run. Because hinges in the product line share the .060 gauge steel construction, installers can expect similar drilling resistance and handling characteristics when using other widths or lengths in the same series alongside this 1-1/2 x 30 bright brass hinge.
The Larsen and Shaw piano hinge is 1-1/2 inches wide when opened and 30 inches long, which suits medium-length doors or lids that benefit from a continuous hinge run.
The bright brass piano hinge uses .060 gauge steel, giving the hinge leaves and knuckle noticeable thickness that supports a solid pivot and consistent movement along the full length.
This 1-1/2 inch wide Larsen and Shaw piano hinge uses #5 flathead screws, so the screw heads seat into the countersunk holes and sit flush with the hinge surface during operation.
The screw holes on this piano hinge are countersunk and spaced 2 inches apart on center, giving an even fastener layout that supports uniform clamping along the hinge leaves.
The 1119EY8FB piano hinge has a bright brass finish over the steel, providing a brass-colored appearance that matches projects calling for brass-toned continuous hinges.
This hinge is part of Larsen and Shaw's high quality piano hinge family, which offers hinge widths from 1-1/16 inch to 3 inches and multiple finishes, including bright brass.
The Larsen and Shaw piano hinge in bright brass, 1-1/2 inches wide by 30 inches long, combines .060 gauge steel with a regular 2 inch on-center hole pattern for straightforward mounting. Using #5 flathead screws across the countersunk holes lets the hinge sit flush and operate cleanly along its 30 inch span. For projects that call for a brass-colored continuous hinge in this size range, this 1119EY8FB model provides a consistent finish and a defined set of dimensions that help standardize your hinge runs.
Sold In: 1 Each
