Larsen and Shaw bright nickel piano hinge is a .060 gauge steel piano hinge that runs the full 72 inch length, creating a continuous pivot that supports long doors or lids along their entire edge, which helps distribute load more evenly in cabinetry and woodworking projects. The hinge is classified as a piano hinge, so it is suited to applications where smooth, aligned movement along a long edge matters, such as bench lids, tall cabinet doors, or built-in access panels. The bright nickel finish provides a clean, metallic appearance on exposed edges, which helps this hinge coordinate with other bright nickel hardware in the same installation. The hinge is branded Larsen and Shaw, giving installers a consistent product identity when matching to existing Larsen and Shaw piano hinge installations or specifying the 1119G02NP part in project documentation.
All cut lengths of this Larsen and Shaw steel piano hinge have countersunk screw holes spaced 2 inches apart on center, which provides a regular, predictable fastener layout along the entire 72 inch length. This pattern gives installers closely spaced attachment points that help hold the door or lid flat against the hinge leaf, supporting alignment along tall doors or long lids. The manufacturer states that 100 screws are required per 6 foot length of hinge, which allows installers to plan fastener quantities in advance when scheduling materials. The hinge uses #5 flathead screws on standard widths, so the countersunk holes are sized to seat those heads flush with the leaf surface for a smoother, snag-resistant hinge line once mounted.
This 2 inch x 72 inch piano hinge functions as a continuous hinge for long cabinet doors, bench seats, lids, and tall access panels where a single, uninterrupted pivot improves alignment. The 72 inch length matches many full-height cabinet or closet applications, so installers can run one hinge from top to bottom without staggering multiple shorter hinges. The 2 inch width provides broader leaf coverage on both the frame and moving panel, helping spread forces over more surface area when doors are opened and closed repeatedly. Because it is a piano hinge in the Hinges, Piano Hinges category, it fits projects that specify continuous hinges rather than individual butt hinges, providing a straight, controlled swing along the entire edge.
The .060 gauge steel used in this Larsen and Shaw piano hinge contributes to a solid leaf profile that helps resist flexing along the 72 inch run, which supports straighter alignment between the door and frame during operation. Countersunk screw holes on 2 inch centers guide the mounting pattern, so installers can follow the pre-set spacing instead of laying out their own, reducing layout time while helping maintain even clamping pressure along the edge. The use of #5 flathead screws on the standard widths means screw heads sit down in the countersinks, helping the leaves close without interference and keeping the knuckle movement clear. Hinge widths in this Larsen and Shaw family, when opened, are specified as 1-1/16 inch, 1-1/4 inch, 1-1/2 inch, 2 inch, and 3 inch, and this 2 inch wide version fits jobs that call for a mid-range width that balances coverage with trim clearances in typical casework. The bright nickel finish completes the working surface with a finished metallic look that pairs well with bright nickel pulls and knobs, supporting a consistent hardware finish story across the project.
The 1119G02NP part is a Larsen and Shaw steel piano hinge, so it provides a continuous hinge line along the full 72 inch edge where an unbroken pivot is required.
The Larsen and Shaw bright nickel piano hinge is 72 inches long, giving installers a continuous 6 foot hinge run for tall doors or long lids without splicing shorter hinges.
This piano hinge is 2 inches wide and 72 inches long, with .060 gauge steel, providing a continuous 6 foot hinge with a 2 inch open width for many cabinet or panel edges.
The Larsen and Shaw piano hinge has countersunk screw holes spaced 2 inches apart on center, which sets a regular fastening pattern along the full length for even support.
This piano hinge uses #5 flathead screws on the standard widths, so screw heads seat into the countersunk holes and allow the leaves to close smoothly along the knuckle.
The hinge has a bright nickel finish, providing a clean, bright metallic appearance that coordinates with bright nickel cabinet hardware in visible hinge applications.
This 2 inch x 72 inch Larsen and Shaw bright nickel piano hinge provides a continuous 6 foot pivot with .060 gauge steel construction, countersunk holes on 2 inch centers, and #5 flathead screw sizing, aligning well with cabinetry and woodworking projects that specify piano hinges. Selecting this 1119G02NP piano hinge from Wurth Baer Supply aligns the job with a defined part number, consistent bright nickel finish, and a hinge geometry built for full-length door or lid edges.
Sold In: 1 Each
