Larsen and Shaw bright nickel piano hinge gives you a 1-1/4 inch wide by 72 inch long continuous steel hinge, so doors, lids, or panels stay aligned along the full length instead of pivoting on individual hinges. This piano hinge is built from .060 gauge steel, which provides a solid leaf thickness for everyday cabinet, casework, or fixture duty where strength and a crisp swing are important. The bright nickel finish provides a clean, reflective surface that suits visible installations where the hinge line is part of the finished look. As a steel piano hinge, it creates a straight, predictable pivot for long doors or lids, helping reduce racking and twist over time. The 72 inch length suits full-height or long-run applications, and the 1-1/4 inch width balances coverage with a narrow sightline for tight, controlled layouts.
Larsen and Shaw's piano hinges use countersunk screw holes spaced 2 inches apart on center along the cut length, so the screw pattern provides frequent fastening points for even clamping of the hinge leaf to the substrate. All piano hinges in this line are designed to use #5 flathead screws, which matches typical small cabinet and casework fastener choices and simplifies bit and pilot sizing during layout. A 6 foot length requires 100 screws, so the fastener count supports a dense, consistent mechanical connection along the entire 72 inch run. The countersunk design lets the flathead screws sit flush with the hinge leaf, helping the door or lid close cleanly without interference from proud fastener heads along the barrel.
The 1-1/4 inch opened hinge width fits well on cabinet doors or panels where edge space is limited, giving you continuous support without crowding adjacent components or reveals. At 72 inches long, this Larsen and Shaw steel piano hinge suits tall cabinet doors, wardrobe panels, or long bench and chest lids that benefit from a full-length pivot. The .060 gauge steel leaf helps the hinge carry everyday furniture and cabinet loads over the full run, so the door weight is spread out rather than concentrated at a few points. The bright nickel finish makes this hinge a match for projects that use other bright plated hardware, keeping the hardware line consistent across doors, drawers, or panel fronts. Because it is a continuous piano hinge, it establishes a single straight axis, which supports precise alignment between door and cabinet on jobs where clean gaps matter.
The 2 inch on-center countersunk screw spacing on this piano hinge gives you a built-in layout rhythm, which speeds marking and drilling while keeping fasteners evenly distributed along the stile or edge. Using #5 flathead screws across the Larsen and Shaw piano hinge line means one screw size applies to this 1-1/4 inch wide hinge, which streamlines tool setup and inventory on the bench. The requirement for 100 screws per 6 foot length signals a dense fastening pattern, which helps keep the hinge seated tight against wood or panel material and supports smooth pivoting over time. The bright nickel finish, described with a lifetime finish, offers a stable surface that resists visual wear in typical cabinet environments, which helps finished work hold its appearance after installation. With hinge widths offered in 1-1/16, 1-1/4, 1-1/2, 2, and 3 inches in this line, the 1-1/4 inch size gives you a mid-narrow option when balancing strength, clearance, and visual scale.
The Larsen and Shaw bright nickel 1119D06NP piano hinge measures 1-1/4 inches wide when opened and 72 inches long, which fits tall doors or long lids needing full-length support.
The 1119D06NP piano hinge is made from .060 gauge steel, giving it a solid leaf thickness for typical cabinet, casework, and furniture applications using a continuous hinge.
The Larsen and Shaw piano hinge uses a bright nickel lifetime finish, which provides a stable, bright surface suited to exposed cabinet and furniture installations.
This Larsen and Shaw piano hinge has countersunk screw holes spaced 2 inches on center along the length, helping distribute clamping force evenly on the door or frame.
The Larsen and Shaw piano hinge line uses #5 flathead screws for this size, which aligns with common cabinet hardware fasteners for a flush mounted installation.
A 6 foot length of this Larsen and Shaw piano hinge uses 100 screws, creating a dense attachment pattern along the entire hinge run for consistent support.
The Larsen and Shaw bright nickel 1-1/4 x 72 steel piano hinge gives you continuous .060 gauge steel support with a lifetime bright nickel finish, a 2 inch on-center countersunk screw pattern, and #5 flathead screw interface for straightforward cabinet and casework runs.
Sold In: 1 Each
