Larsen and Shaw steel piano hinge in antique brass at 1-1/16 inch by 72 inch spans long edges, so doors, lids, or panels pivot smoothly along the full length instead of on short hinge points. The piano hinge construction spreads load evenly along the joint, which supports straighter alignment over time. The .060 gauge steel material provides a solid leaf thickness, which supports frequent opening and closing in typical woodworking and cabinet applications. The antique brass finish gives the steel hinge a classic tone, which helps it match traditional or warm-toned projects. This hinge belongs to the piano hinge product class, so it fits applications needing continuous support instead of discrete butt hinges. The Larsen and Shaw brand identification signals a consistent pattern across their piano hinge line, which simplifies matching this 72 inch length with other widths and finishes in the same family.
This Larsen and Shaw steel piano hinge uses countersunk screw holes spaced 2 inches on center along cut lengths, which gives a predictable mounting pattern for laying out drilling operations. The countersunk design lets #5 flathead screws seat flush in the hinge leaf, which helps the door or panel close without interference from screw heads. For a 6 foot, 72 inch hinge length, the pattern uses 100 screws, which distributes holding strength at regular intervals along the joint. All hinge widths in this line use #5 flathead screws except the 3 inch wide versions that use #6 flathead screws, so this 1-1/16 inch width matches the #5 sizing. That consistent screw specification helps installers plan fastener selection for multiple hinge widths in the same project without changing bit or pilot practices.
This 1-1/16 inch by 72 inch Larsen and Shaw steel piano hinge suits applications needing a continuous pivot over a 6 foot span, such as tall cabinet doors, wardrobe panels, or long lids on chests and benches. The piano hinge class design with a full-length knuckle supports loads across the entire run, which helps keep door reveals more consistent from top to bottom. The antique brass finish gives the hinge a traditional appearance along the full 72 inch length, which aligns well with classic cabinetry, furniture pieces, or restoration work using warm metal tones. The .060 gauge steel provides a substantial yet manageable thickness, which balances strength with a profile that still fits typical door and frame margins. The 1-1/16 inch opened width keeps the leaf footprint modest, which is useful when stile or case edges are narrow.
The countersunk screw holes spaced 2 inches on center along the hinge length provide a repeating layout, which simplifies translating the pattern to workpieces for drilling. This regular spacing supports even clamping and fastener pull across the 72 inch run, which helps the leaf sit flat to the substrate. Using #5 flathead screws in this 1-1/16 inch piano hinge keeps the fastener size consistent across most widths in the Larsen and Shaw line, which reduces variation in pilot hole sizing and driver setup between similar hinges. The requirement for 100 screws per 6 foot length means each segment of the hinge contributes to holding strength, which supports doors or lids that experience frequent use without concentrating stress at only a few points. Together, the steel gauge, screw pattern, and countersunk design support a straight, repeatable installation along the full hinge length.
The Larsen and Shaw hinge 1119C07BA measures 1-1/16 inch in opened width and 72 inches in length, which suits full-height cabinet doors or long lids needing continuous support.
This piano hinge uses .060 gauge steel with an antique brass finish, which provides solid hinge strength while delivering a warm, traditional appearance along the full length.
Cut lengths of this Larsen and Shaw piano hinge have countersunk screw holes spaced 2 inches on center, which creates a consistent mounting pattern for drilling and fastening.
This 1-1/16 inch wide piano hinge is designed for #5 flathead screws, which allows the screw heads to sit flush in the countersunk holes for smooth door or lid movement.
A 6 foot, 72 inch length of this Larsen and Shaw piano hinge uses 100 screws, which spreads holding power evenly along the continuous hinge run.
This hinge is in the Larsen and Shaw piano hinge line, which is available in multiple widths and five finishes, supporting coordinated hardware across related projects.
The Larsen and Shaw steel piano hinge antique brass 1-1/16 inch by 72 inch design combines .060 gauge steel, a lifetime finish, and a 2 inch on-center countersunk screw pattern to support continuous 6 foot joints. The 100-screw layout on each 72 inch length distributes fastening along the full span, which suits tall doors or long lids needing stable, full-length support. Choosing this 1119C07BA piano hinge aligns dimension, finish, and mounting details in a single component, ready for continuous-hinge cabinet and furniture projects.
Sold In: 1 Each
