Steel piano hinge from Larsen and Shaw in a 1-1/16 inch by 72 inch size provides a continuous pivot along the full run of a lid or door, which helps spread load and reduces point stress on cabinets, chests, or fixtures. The hinge is made from .060 gauge steel, giving a consistent leaf thickness that supports predictable routing or mortising depths when laying out a project. A bright nickel finish on the steel hinge creates a clean, metallic surface that works well where the hinge will be visible and needs a uniform appearance across multiple cabinets. The hinge belongs to the piano hinge category, so it suits long, straight applications where alignment over the entire length matters more than decorative knuckles. The product is identified by manufacturer part number 1119C07NP, which helps match this exact size and finish when repeating a build or servicing an existing installation.
All cut lengths of this Larsen and Shaw steel piano hinge are produced with countersunk screw holes spaced 2 inches apart on center, giving installers a clear fastening rhythm along the entire 72 inch length. This regular spacing supports even load transfer into the substrate and simplifies marking and predrilling on repetitive cabinet work. The hinge uses #5 flathead screws at this 1-1/16 inch width, so the countersinks are matched to that head size, helping the screw heads nest properly and allowing the leaves to close without rubbing on fasteners. The hinge width and .060 gauge leaf thickness give a defined footprint on the edge of the workpiece, which aids in planning clearances and edge distances during layout.
This Larsen and Shaw piano hinge, at 1-1/16 inch opened width and 72 inch length, aligns well with long, relatively narrow doors, lids, or panels where continuous support is preferred over single-butt hinges. The extended length lets the hinge follow the full edge, which can reduce racking on tall cabinet doors or long bench lids by tying the entire edge into one pivot line. Because the hinge is built from .060 gauge steel, it supports applications where a metal leaf of known thickness helps coordinate with shallow mortises or surface-mount layouts on wood or similar materials. Being in the piano hinge class, it is suited to straight runs where the installer wants consistent gap lines and even motion across the whole opening.
The bright nickel finish on this steel piano hinge provides a consistent surface color from end to end, supporting projects where multiple hinges must present the same visual tone across a bank of cabinets. .060 gauge construction keeps the leaves uniform, which helps installers rely on the hinge as a repeatable reference when setting reveals or aligning multiple doors to a shared frame. Countersunk holes 2 inches on center establish a defined screw pattern, so each hinge in a run can be laid out identically, reducing layout time and helping maintain straight lines during fastening. The use of #5 flathead screws for this width means the fastener geometry is tuned to the countersinks, helping the hinge operate smoothly by keeping bearing surfaces clear as the leaves rotate.
The Larsen and Shaw piano hinge has a 1-1/16 inch opened width and a 72 inch length, which suits long, narrow lids or doors that benefit from continuous support.
The hinge is made from .060 gauge steel, giving a consistent leaf thickness that supports predictable routing, mortising, and alignment across multiple identical installations.
The 1119C07NP hinge has a bright nickel finish, providing a uniform metallic look that coordinates with other bright nickel components in visible cabinet or furniture applications.
All cut lengths have countersunk screw holes spaced 2 inches apart on center, creating an even fastening pattern that supports straight alignment over the 72 inch run.
For this 1-1/16 inch width hinge, Larsen and Shaw specifies #5 flathead screws, so the screw heads sit properly in the countersinks and allow smooth hinge movement.
This bright nickel steel piano hinge is identified by manufacturer part number 1119C07NP, which helps match the same size, gauge, and finish on future jobs.
The Larsen and Shaw bright nickel 1-1/16 inch by 72 inch steel piano hinge combines a .060 gauge leaf, continuous length, and 2 inch on-center countersunk holes to support straightforward layout on long doors or lids. The matched #5 flathead screw specification and bright nickel finish tie mechanical function and appearance together for cabinetry or furniture where the hinge line stays visible. For work that calls for a continuous, steel piano hinge with these exact dimensions and finish, this 1119C07NP model from Wurth Baer Supply offers a clearly defined option to standardize around.
Sold In: 1 Each
