Larsen and Shaw bright brass piano hinge gives you a continuous .060 gauge steel hinge along a 72 inch run, which helps distribute door or lid loads across the full length for smoother movement in cabinetry and similar woodworking projects. The 2 inch opened width provides a broad bearing surface, which supports larger doors or panels where point-load hinges are less desirable. Bright brass finish delivers a matching appearance where brass hardware is specified, helping projects maintain a consistent look across visible hinge lines. Being part of Larsen and Shaw's high quality steel piano hinge line means this hinge is designed as a continuous hinge solution for long panels rather than short, discrete butt hinges. The 72 inch length supports full-height or oversized applications that benefit from a single, uninterrupted hinge leaf instead of multiple shorter segments aligned in the field.
All cut lengths of this Larsen and Shaw steel piano hinge use countersunk screw holes spaced 2 inches apart on center, which provides a regular, predictable fastening pattern during layout along the frame and door edge. The pattern uses #5 flathead screws on this 2 inch wide version, so the screw heads sit flush in the countersinks when installed with the correct screw size. A 6 foot length of hinge from this line requires 100 screws, which indicates a high fastener count per run and supports firm attachment across the entire length when used on longer doors or lids. This specific hinge is part of the bright brass finish offering within the broader range, so it can be coordinated with other Larsen and Shaw bright brass piano hinge sizes in the same project.
This 2 inch by 72 inch Larsen and Shaw piano hinge serves projects that need a full-length continuous hinge, such as tall cabinet doors or long bench lids that benefit from even support along the hinge side. The bright brass finish suits installations where exposed hinges are part of the finished look, such as decorative cabinetry or furniture pieces using other bright brass components. With hinge widths (opened) in this line spanning 1-1/16, 1-1/4, 1-1/2, 2, and 3 inches, this 2 inch size sits in the wider range, supporting heavier or larger faces than the narrow widths. The 72 inch length also aligns with applications using other lengths from the same family, since the line includes 30 and 48 inch options, so layouts can mix lengths while keeping the same visual style.
The countersunk screw holes spaced 2 inches apart on center across this Larsen and Shaw .060 gauge steel piano hinge simplify marking and drilling, because the installer can follow the factory pattern rather than laying out each location independently. Using #5 flathead screws on this 2 inch wide hinge keeps the screw heads level with the hinge surface when seated in the countersinks, which allows the hinge leaves to close without interference from proud screw heads. Knowing that a 6 foot length from this hinge family uses 100 screws highlights the dense fastening pattern, which spreads holding power across many small attachment points instead of relying on a few larger fasteners. The continuous steel construction along the full 72 inch span combines with the frequent screw spacing to support consistent alignment of the moving edge through the door or lid stroke.
The Larsen and Shaw bright brass piano hinge in this listing is 2 inches wide when opened and 72 inches long, which suits full-length cabinet doors or long lids needing continuous support.
This bright brass hinge is made from .060 gauge steel, which provides a sturdy continuous leaf for doors or panels that see repeated opening cycles in typical woodworking applications.
The Larsen and Shaw steel piano hinge has countersunk screw holes spaced 2 inches apart on center, which creates a consistent fastening pattern along the full hinge length.
This 2 inch wide piano hinge from Larsen and Shaw is designed for #5 flathead screws, so the screws sit flush in the countersunk holes and allow the hinge leaves to close properly.
A 6 foot length of Larsen and Shaw piano hinge from this line uses 100 screws, which spreads holding strength over many attachment points along the run.
Larsen and Shaw piano hinges in this family are available in Antique Brass, Bright Brass, Bright Nickel, Black Powder Coat, and Bright Zinc, supporting different project finish schemes.
The Larsen and Shaw bright brass 2 inch by 72 inch .060 gauge steel piano hinge combines continuous steel construction, dense 2 inch on-center countersunk screw spacing, and #5 flathead screw use to support long doors or lids in woodworking projects. The bright brass finish aligns with other bright brass components across a build, while the continuous 72 inch length and distributed screw pattern help maintain alignment along the full hinge edge. For projects calling for a high quality bright brass piano hinge with a predictable mounting layout, this Larsen and Shaw 1119G02FB model from Wurth Baer Supply offers a focused, job-ready option.
Sold In: 1 Each
