
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Grass 6610 series drawer slides use a standard 3/4 extension design, so drawers travel out far enough for practical access while keeping members well supported for everyday cabinet use. The right-hand drawer member in white is epoxy coated, which provides a consistent sliding surface that supports smooth travel in typical woodworking environments. This member is part of a bottom mount system that also has additional holes for side mount, giving flexibility in how the slide is fixed to the cabinet. A standard 1/2 inch side clearance is built in, so case and drawer construction can follow familiar Euro slide practices without custom offsets. The single captive design will absorb tolerances up to 2 mm and still run smooth, which helps installations perform well even when carcass or drawer widths vary slightly from plan.
This right-hand drawer member is part of a bottom mount slide series with additional holes for side mount, so fabricators can fasten the slide from below or at the side depending on cabinet design. Holes in both members are set up for #6 flat head Phillips or Euro screw, giving installers a choice of common fasteners that match their tooling and shop standards. The standard 1/2 inch side clearance supports predictable alignment between drawer and case when used with complementary members from the 6610 series. Parallel self closing action at 2-5/8 inches of travel interacts with the overall slide geometry, guiding the drawer into a consistent closed position relative to the cabinet front.
The Grass 16-1/2 inch drawer slide right-hand member is sized at 400 mm, aligning with metric-based cabinet planning that still targets a 16 inch nominal length. As a component of the 6610 series bottom mount system with extra side mount holes, it suits cabinet designs that may need either mounting style while keeping the same member length. Standard 1/2 inch side clearance lets this member integrate into Euro-style drawer boxes that follow that gap convention, which is common in both shop-built and production cabinetry. The 32 mm system compatibility supports cabinets drilled on line-boring machinery, tying the slide member into rows of shelf and hardware holes used across many carcass designs.
The single captive design that absorbs tolerance up to 2 mm lets this drawer member perform well when drawer box or cabinet sides are slightly out of nominal dimension, which is common in real shop conditions. Because the design still runs smooth within that tolerance range, installers can rely on consistent opening and closing without chasing minor width deviations across multiple drawers. The epoxy coated finish on this white right-hand member presents a uniform running surface along the length, which works together with the captive geometry to maintain repeatable motion under normal cabinet loads.
The 100 lb rating per ANSI/BHMA testing gives this right-hand drawer member a defined performance target when used in the complete slide system, which matters when specifying slides for drawers that carry tools, hardware, or heavier kitchen items. Knowing the series is tested to that level helps designers align drawer sizes and contents with the slide capacity instead of assuming light-duty use. The 3/4 extension travel balances access with support, so even at full designed extension the drawer retains enough engagement on the slide members for stable motion under those rated loads.
Parallel self closing action beginning at 2-5/8 inches of travel helps the drawer settle into the same closed position each time, which supports consistent front reveals when cabinets are built to matching face dimensions. This self closing behavior also works with the standard 1/2 inch side clearance and captive design, so slight side-to-side variations are absorbed while the front alignment remains visually consistent. Holes for #6 flat head Phillips or Euro screw across both members allow shops to standardize on a screw style that fits their jigs and drivers, which can speed installation on production runs using this Grass America 6610 series member.
The Grass 6610 series drawer slides provide 3/4 extension, which lets the drawer open far enough for access while keeping the slide members engaged for support during regular use.
The Grass right-hand drawer member works with a standard 1/2 inch side clearance, so cabinet and drawer widths can follow common Euro slide spacing practices in new builds or repeat jobs.
The Grass 6610 series slide system carries a 100 lb rating per ANSI/BHMA testing, which supports specifying these slides for drawers expected to hold typical residential or shop storage loads.
The Grass 6610 series has parallel self closing action beginning at 2-5/8 inches of travel, which draws the drawer into a consistent closed position and helps maintain uniform front alignment.
The Grass 63737-09 right-hand drawer member is 32 mm system compatible, allowing it to integrate into cabinets drilled on 32 mm line-boring patterns for efficient production setups.
This 16-1/2 inch Grass 6610 series member is designed as bottom mount and also has additional holes for side mount, giving flexibility to match cabinet construction and shop preferences.
The Grass 16-1/2 inch drawer slide right-hand drawer member 63737-09 combines 3/4 extension travel, a 100 lb ANSI/BHMA-tested rating, and 32 mm system compatibility to fit many cabinet layouts. The bottom mount design with extra side mount holes supports different case constructions, while standard 1/2 inch side clearance and single captive tolerance absorption up to 2 mm help drawers run smoothly across a range of build conditions. For projects based on Grass America 6610 series geometry, this right-hand white epoxy coated member aligns with familiar Euro practices and production workflows.
Sold In: 100 Each