Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Hickory Hardware Skylight 18 inch pull is a long cabinet handle built around an 18 inch center to center dimension, so it spans wide drawer fronts or doors for a continuous, straight-line grip. The pull uses a simple square and 90 degree angle geometry, which gives it a contemporary look that aligns with modern kitchen cabinet layouts. Its overall length of 18-1/2 inches lets the handle visually anchor larger fronts while keeping screw holes at the standard 18 inch spread for layout consistency. A projection of 1-1/4 inches brings the grip comfortably away from the face, creating clearance for fingers during everyday use. With a 1/2 inch width, the pull presents a slim profile that still reads clearly across the cabinet face. The combination of proportioned length, projection, and width supports a balanced appearance along with a practical handhold.
The 18 inch center to center layout positions the mounting holes at a fixed distance that suits long drawers or tall doors, so drilling layouts can follow a repeatable pattern across multiple fronts. With an overall length of 18-1/2 inches, the pull extends slightly beyond the hole spacing, which creates a defined end point that can help align to stiles or drawer edges during layout. The 1-1/4 inch projection sets the handle off the face, allowing room for fingers to wrap behind the bar during opening and closing. Its 1/2 inch width keeps the footprint lean, which works well where multiple doors meet and space between handles is limited. Together, these dimensions give installers clear reference points for placing the pull relative to cabinet edges and for matching existing hole patterns built around an 18 inch spread.
This pull is part of the Skylight collection, which is inspired by contemporary kitchen design built around squares and 90 degree angles, so it suits cabinet runs that favor straight, clean lines. Its 18 inch center to center measurement lends itself to wider drawers, pantry doors, or tall utility fronts where a longer grip helps distribute hand contact across more of the face. The 18-1/2 inch length allows the handle to span much of the front, so it visually anchors large surfaces without crowding the edges when positioned with typical setbacks. Because the pull has a projection of 1-1/4 inches, it creates a useful gap between the hardware and the cabinet, supporting comfortable operation on heavier drawers or doors. The Elusive Golden Nickel finish defines the color and sheen of the pull, supporting coordinated layouts where all visible hardware carries the same Elusive Golden Nickel tone.
The 18 inch center to center handle dimension lets installers base drilling jigs or templates on a single, known spacing, which reduces layout variation across a run of cabinets. When replacing or matching existing 18 inch center to center hardware, this pull preserves that hole spacing, limiting the need for new drilling when the pattern already exists. The 1/2 inch width keeps the bar visually light, helping maintain even margins around the hardware when installed between tight reveals or near adjacent doors. Its 1-1/4 inch projection brings the gripping surface into a more accessible position, assisting users who prefer a deeper hold on long drawers or tall doors. Constructed from zinc, the pull provides a stable structure beneath the Elusive Golden Nickel finish, which supports repeated daily operation on frequently used cabinets. The defined square and 90 degree angle form keeps sightlines straight, supporting precise visual alignment from cabinet to cabinet.
The 18 inch center to center measurement is the distance between the mounting holes, which guides drilling layouts and supports direct replacement of other 18 inch center to center pulls.
The Hickory Hardware Skylight 18 inch pull has an overall length of 18-1/2 inches, so the handle extends slightly past the mounting holes to visually frame the installation area.
This Elusive Golden Nickel cabinet pull projects 1-1/4 inches from the cabinet face, providing space for fingers behind the handle during opening and closing.
The Belwith Keeler Skylight pull bar is 1/2 inch wide, giving a slim profile while still offering a flat surface to grip on cabinet doors and drawers.
The HH075337-EGN cabinet pull is made from zinc, providing a solid base structure for the Elusive Golden Nickel finish during regular cabinet use.
This Skylight series pull uses an Elusive Golden Nickel finish, giving the handle its defined color and sheen for coordinated hardware layouts.
The 18 inch center to center mounting, 18-1/2 inch overall length, and 1-1/4 inch projection position this pull as a straightforward choice where long cabinet hardware is needed. The 1/2 inch width and square, 90 degree angle form align with the Skylight collection focus on contemporary geometry, so the pull fits modern cabinet runs that rely on clean lines. Its zinc construction and Elusive Golden Nickel finish tie directly to the HH075337-EGN part number, helping match product details when adding or updating hardware. For projects built around 18 inch center to center layouts, this Belwith Keeler Skylight pull offers a defined size and finish profile ready to integrate into new or existing cabinet fronts.
