Hickory Hardware Skylight pull is a zinc cabinet handle from the Skylight collection with a stainless steel finish, so it delivers the squared contemporary look of modern kitchen design while using a sturdy base metal suited to everyday cabinet use. The 5-1/16 inch (128 mm) center to center mounting dimension sets a consistent handle spacing, which helps keep door and drawer layouts aligned across a run of cabinets. Overall length of 5-7/16 inch gives a bit of overhang past the mounting holes, which provides finger clearance at the ends and keeps hands away from the cabinet face. A projection of 1-1/4 inch brings the grip out from the door, allowing fingers to wrap behind the pull for a secure grab on doors or drawers. The 3/8 inch width keeps the profile slim, which supports a clean, architectural look that pairs well with flat-panel fronts.
This Belwith Keeler cabinet pull uses a 128 mm (5-1/16 inch) center to center mounting dimension, which is sized for standard cabinet drilling jigs used in many shops and on site. That fixed spacing supports repeatable installation along drawer banks because each front can be bored the same way. The 5-7/16 inch overall length defines the edge-to-edge footprint on the door or drawer, which matters when working near panel edges or adjacent pulls. With a projection of 1-1/4 inch, the handle stands off from the face enough to clear typical door thicknesses while still keeping the hardware close to the cabinet for a tight visual line. The 3/8 inch width creates a slim contact area, making it easier to line up multiple pulls without visually crowding narrow rails.
This modern square cabinet pull is part of the Skylight collection, which is inspired by contemporary kitchen design that reduces forms to the square and 90 degree angle, so it suits flat-panel and slab cabinet fronts that share the same geometry. The 5-1/16 inch center to center drilling dimension positions it in the mid-size pull range, which fits well on standard kitchen and bath base cabinets, wall cabinets, and medium-width drawers where a bar longer than the mounting spread is desired. The stainless steel finish helps it visually align with stainless appliances, sinks, and fixtures, tying together fronts and surrounding metal elements in the same workspace. Its 5-7/16 inch overall length provides enough span to feel substantial on a drawer without overwhelming narrower fronts, supporting consistent sizing across upper and lower cabinets. Because this pull belongs to the Skylight collection, it can be used in layouts that repeat the same squared aesthetic across multiple rooms in a project.
The defined 128 mm center to center dimension gives a precise boring target, which supports shop-made drilling templates and CNC programs that rely on metric spacing for speed and consistency. A projection of 1-1/4 inch provides predictable hand clearance for both doors and drawers, so once this pull is chosen, the same geometry can be repeated across a bank without grip changes from cabinet to cabinet. The 3/8 inch width and square profile reflect the Skylight emphasis on proportion, meaning the visual mass of the handle stays consistent as you run multiple pulls in a line. The combination of zinc material and stainless steel finish ties the structural and visual aspects together: zinc forms the base body suited for decorative hardware, while the finish presents a stainless appearance that coordinates with nearby metalwork. The Belwith Keeler manufacturer designation HH075328-SS identifies this exact size and finish, which is useful when repeating the same pull throughout future phases on the same job.
The HH075328-SS pull has a 5-1/16 inch (128 mm) center to center drilling dimension, which sets consistent hole spacing for doors and drawers across a project.
This Skylight collection pull has an overall length of 5-7/16 inch, so it extends slightly beyond the 128 mm mounting spread for added grip area at each end.
The HH075328-SS pull is made from zinc with a stainless steel finish, combining a decorative hardware base metal with a finish that visually matches stainless elements.
The Skylight pull projects 1-1/4 inch from the cabinet face, providing space for fingers to hook behind the bar while keeping a low-profile look.
The handle is 3/8 inch wide, giving a slim, square-edged profile that supports the clean architectural lines of contemporary cabinet runs.
This 128 mm center to center pull is the Skylight collection HH075328-SS from Belwith Keeler, sold under the Hickory Hardware name.
The Hickory Hardware Skylight pull with 5-1/16 inch (128 mm) center to center spacing, 5-7/16 inch overall length, and 1-1/4 inch projection gives a defined geometry that suits contemporary cabinets using square lines. The zinc construction with stainless steel finish supports decorative cabinet use while visually tying into stainless fixtures. For jobs that call for a consistent, modern handle in this specific size and finish, the Belwith Keeler HH075328-SS provides a repeatable choice you can apply across doors and drawers in the same run.
Sold In: 1 Each
