Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Skylight 12 inch center to center pull from the Skylight collection is a zinc cabinet handle in an Elusive Golden Nickel finish, so it brings a contemporary metallic look that matches modern kitchen and bath jobs. The design is built around the square and the 90 degree angle, which gives doors and drawers straight, clean lines that sit well with flat-panel fronts and other architectural hardware. The pull length of 12-7/16 inches creates a long gripping surface, helping doors feel balanced on tall pantry cabinets or wide drawers. A projection of 1-3/8 inches provides hand clearance off the fascia, which supports comfortable use on thicker drawer fronts. The 7/16 inch width keeps the profile visually light, so it reads as sleek rather than bulky on narrow fronts or multiple adjacent drawers.
The 12 inch center to center dimension sets the hole spacing for this Skylight pull, so layout on doors and drawers can be repeated quickly across a full bank of cabinets. With 12-7/16 inches overall length, the ends extend beyond the mounting points, which helps visually center the bar on wider faces and keeps the pull looking balanced when installed in a run. The 1-3/8 inch projection defines how far the pull stands off the cabinet front, which affects how fingers clear decorative edges or adjacent trim. A 7/16 inch width keeps the bar slim across the grain, so it sits comfortably on narrow rails or drawer fronts without overpowering them.
The Skylight collection was inspired by contemporary kitchen design, so this 12 inch center to center pull fits clean-lined cabinet runs where straight geometry matters. Its square and 90 degree angle profile matches flat-panel or slab doors, creating continuous horizontal or vertical lines across banks of wall and base cabinets. On tall pantry doors, the 12-7/16 inch length gives the hand a longer area to grab, which is helpful when opening from different heights along the stile. For wide drawers, the 12 inch center to center layout places mounting points toward the outer thirds of the front, which supports an even appearance across stacked drawer configurations. The Elusive Golden Nickel finish lets this pull sit comfortably in jobs that already use nickel tones, tying together hinges and other decorative hardware in the same space.
The fixed 12 inch center to center spacing is the key reference dimension, so once that drilling pattern is set, installers can repeat it across doors and drawers for consistent hardware alignment. The 12-7/16 inch overall length leaves small overhangs past each mounting point, which visually frames the screw locations and helps the pull look centered even when used on different cabinet widths. With a 1-3/8 inch projection, the pull stands off the face enough to clear common door and drawer front thicknesses, supporting a comfortable grip without crowding nearby cabinets. The 7/16 inch width keeps the pull slender, which helps maintain even reveals between adjacent fronts because the hardware does not visually widen tight gaps. Zinc material construction provides a uniform metal body, so each HH075336-EGN pull in a project has consistent mass and appearance from one cabinet to the next.
The HH075336-EGN pull has 12 inch center to center spacing, a 12-7/16 inch overall length, 1-3/8 inch projection, and 7/16 inch width, which together define drilling, reach, and visual scale on the cabinet.
The Skylight pull is made from zinc, giving it a solid metal body that supports a consistent feel on doors and drawers across a full installation.
This pull uses an Elusive Golden Nickel finish, providing a warm nickel tone that coordinates with other nickel hardware while maintaining a contemporary look.
The Skylight collection was inspired by contemporary kitchen design using square and 90 degree forms, so this pull aligns well with modern cabinet styles.
A 1-3/8 inch projection sets the pull off the cabinet face, providing finger clearance that supports comfortable gripping on doors and drawers.
The 12 inch center to center measurement indicates the distance between mounting holes, guiding drilling layout and helping keep pulls aligned across multiple cabinets.
The Skylight 12 inch center to center pull in Elusive Golden Nickel pairs square, 90 degree geometry with zinc construction, so it suits contemporary cabinet lines that favor clean, architectural hardware. With 12-7/16 inch overall length, 1-3/8 inch projection, and 7/16 inch width, it provides repeatable drilling and a comfortable hand clearance that carries across doors and drawers in a full kitchen or casework project. Choosing the HH075336-EGN pull keeps dimensions, finish, and feel consistent anywhere this Skylight design is used.
Sold In: 1 Each
