Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
Knape and Vogt 8400 drawer slides provide a 10 inch full extension action, letting the drawer travel its full length so the cabinet opening can be used effectively. The side mount design positions the slides on the cabinet sides, which keeps the drawer box bottom clear for standard construction methods. Ebony black finish gives the slides a dark appearance that blends with darker casework and hardware layouts. The ball bearing construction supports smooth movement along the slide members, which helps drawers open and close with consistent effort in day-to-day use. The hold-in anti-rebound feature pulls the drawer closed at the end of travel and resists bounce-back, so the drawer stays seated in the cabinet until it is intentionally opened again. The non-handed configuration means the same slide design works on either side, reducing part variation during layout and installation.
The 8400 series uses a side mount configuration, placing one member on the cabinet side and one on the drawer side so installers can work off flat interior faces. Recommended fasteners are #7 x 1/2 inch Phillips truss head, which match the slide hole sizing and sit flat against the steel to spread load along the mounting surface. The specified side clearance of 1/2 inch plus 1/32 inch minus 0 inch per side directs the cabinet and drawer sizing so the ball bearing members run freely without excessive play. The 32 mm pattern provides a reference for boring locations, tying slide mounting holes to other hardware using the same system for coordinated layouts.
The KV model 8400 in a 10 inch length suits compact drawers and pullouts where full extension is needed within a short depth, such as smaller base cabinets or utility compartments. The side mount layout is suited to casework with solid or panel sides that accept fasteners along the length of the slide. Ebony black finish coordinates with darker interior finishes, which can benefit built-ins where visible hardware should recede visually. The 1-13/16 inch slide height fits common drawer side heights, leaving room above and below when multiple drawers are stacked in a cabinet. Because the slides are non-handed, the same model can be used on both left and right sides, simplifying inventory for repetitive cabinet runs.
The ball bearing design of the 8400 series supports smooth linear motion between cabinet and drawer members, which can help drawers track consistently under normal use. The hold-in anti-rebound function keeps the drawer settled at the closed position, which can matter in situations where vibration or frequent opening and closing would otherwise cause partial opening. The lever disconnect allows the drawer member to release from the cabinet member, helping installers remove drawers during finishing, alignment, or service tasks without disturbing the cabinet mounting points. With side clearance defined at 1/2 inch plus 1/32 inch minus 0 inch on each side, cabinetmakers can dimension drawer boxes to repeatable widths so the slides engage correctly from one cabinet to the next. The 32 mm pattern ties the slide mounting to system-bored hole lines, aligning drawers, hinges, and other hardware on a consistent grid. Recommended #7 x 1/2 inch Phillips truss head fasteners match the slide holes, which helps the slide seat firmly against wood panels or similar substrates during installation.
The 8400B EB 10 is a Knape and Vogt 8400 series side mount ball bearing drawer slide, which supports smooth full extension motion along cabinet and drawer members.
The 8400B EB 10 requires 1/2 inch plus 1/32 inch minus 0 inch side clearance per side, guiding drawer box width so the slides operate freely without excess looseness.
The 8400B EB 10 has a 10 inch length and a height of 1-13/16 inch, which helps determine drawer depth and side height during cabinet design.
The lever disconnect on the 8400B EB 10 separates the drawer member from the cabinet member, allowing drawers to be removed for fitting, finishing, or service without moving the cabinet members.
The 8400B EB 10 uses a 32 mm pattern and is recommended for #7 x 1/2 inch Phillips truss head fasteners, coordinating with system-bored cabinets and matching the slide hole sizing.
The 8400B EB 10 has an ebony black finish and is non-handed, so the same slide model can be used on either side of the drawer for simplified planning.
The Knape and Vogt 8400 drawer slides in 10 inch full extension form pair side mount installation with a defined 1/2 inch side clearance, giving cabinetmakers concrete sizing targets. Ebony black finish, 1-13/16 inch height, and 32 mm pattern help this model integrate into dark casework and system-bored production runs. Lever disconnect, ball bearing construction, and hold-in anti-rebound behavior support drawers that travel smoothly and stay closed at rest. For projects matching these dimensions and layout details, the 8400B EB 10 provides a clearly defined slide option.
Sold In: 10 Set
