
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
Knape and Vogt 1805 series drawer slides provide a side mount drawer slide solution for cabinet projects where a 16 inch 3/4 extension slide is specified. The 3/4 extension design lets the drawer open most of the way while still supporting the drawer for typical cabinet use. The side mount configuration positions the slide on the cabinet and drawer sides, aligning with common casework construction so layouts stay predictable from job to job. The slide height of 35.5 mm keeps the member low on the drawer, which helps when clearing face frames or tight openings. The white finish matches the specified white epoxy coating noted for this euro slide category, so the hardware visually blends with light-colored interiors. The 1805-97 WH 400 designation identifies this unit as a left hand drawer member component, useful when organizing parts for multi-drawer installations.
This 1805 series component is part of a side mount drawer slide system, so the working clearance is established between the drawer sides and cabinet sides. The specified side clearance of 1/2 inch plus, 1/32 inch minus on each side guides drawer box width calculations, helping installers hit a predictable running fit. With a 35.5 mm slide height, the member occupies modest vertical space on the drawer side, giving room to position the slide relative to drawer bottom or top rails. The 3/4 extension travel range supports common storage drawers where full extension is not required, while still allowing good access to contents near the front and center of the drawer box.
The SAP description identifying this part as 16 LH DRW MBR, WHT 3/4 EXT defines it as a 16 inch left hand drawer member in white for 3/4 extension applications. In a typical cabinet layout, this member mounts to the left side of the drawer box as part of the 1805 series side mount system. The white finish coordinates with the white euro slide family described for this category, which is often selected for melamine or light interior casework. The 32 mm pattern on the member supports use in cabinet boxes built around the 32 mm drilling system, tying into line-boring patterns on cabinet sides. Because the recommended fasteners are #6 x 5/8 inch Phillips pan head, installers can standardize on that size when mounting both drawer and cabinet members, which simplifies tool setup on site or in the shop.
The self-closing design built into the 1805 series helps the drawer return to its seated position at the end of the stroke, which supports consistent closing feel across multiple drawers on a run. The positive double-out stop in this series controls outward travel, which helps prevent drawers from being pulled too far during use, protecting both slides and drawer joinery over time. The lift out disconnect feature lets the drawer be removed from the cabinet member without disturbing the installed positions, which supports finishing, adjustments, or service work with minimal disruption. When the specified side clearance of 1/2 inch plus, 1/32 inch minus is followed, the slides are set up to operate within their intended tolerance band, which helps maintain smooth travel. Selecting this 1805-97 WH 400 left drawer member with its defined 16 inch length and 3/4 extension behavior gives installers a known reference when planning cabinet depths, drawer box lengths, and rail positions in a project.
The 1805-97 WH 400 is a Knape and Vogt 1805 series side mount drawer slide component designed as a left hand drawer member for 3/4 extension drawer applications.
The 1805-97 WH 400 corresponds to a 16 inch 3/4 extension slide, so it suits drawer designs built around a 16 inch nominal slide length with partial extension travel.
This 1805 series member is specified for side clearance of 1/2 inch plus, 1/32 inch minus on each side, guiding drawer box width relative to the cabinet opening.
The Knape and Vogt 1805 series uses a 32 mm pattern, matching cabinet systems built around 32 mm line boring for consistent hole spacing and alignment.
The recommended fasteners are #6 x 5/8 inch Phillips pan head screws, which match the mounting holes and support secure attachment to drawer and cabinet sides.
The 1805-97 WH 400 is specified with a white finish in the 1805 series, matching the white epoxy coated euro slide category for light interior cabinetry.
The Knape and Vogt 1805-97 WH 400 left hand drawer member provides a 16 inch, 3/4 extension, side mount component with white finish, 32 mm pattern, specified side clearance, and self-closing design. These defined details help align drawer box sizing, hole boring patterns, and closing action across a project. For builds using the 1805 series euro slides, this left drawer member fits into a coordinated set of parts, supporting consistent drawer performance in cabinet installations supplied by Wurth Baer Supply.
Sold In: 100 Each