
Order by 24/7 by web, contact our sales reps or call by phone.

What you need, when you need it, all in one place.

Most orders ship same day.

Advice and support from knowledgeable professionals.
3-1/4 inch 2-piece cable grommet gives a clean, defined opening for routing wires through furniture and work surfaces. The round plastic design manages cable transitions through cutouts, so wires pass a fixed point without scraping raw edges or moving around loosely.
This style grommet has two pieces: a grommet cap and a hole liner. The hole liner sets a consistent 3-1/4 inch bore hole interface, while the cap finishes the opening to match the cutout, which helps keep edges protected in repeated use.
The cap has a pivot hinge hole for wire. That pivot hinge allows the wire opening in the cap to swing, so cables can be positioned through the cap while the rest of the cap stays seated in the liner, which helps maintain a tidy surface appearance when wires change.
The grommet is a black plastic part from Hardware Concepts, Inc. The black color lets the opening visually blend into darker tops or cabinets, while the plastic material provides a smooth bearing surface for cables as they move.
The 6650 3-1/4 inch 2-piece cable grommet is sized for a 3-1/4 inch bore hole diameter. That bore dimension guides drilling so the liner seats properly in the cutout and the cap fits the liner without rocking.
As a round plastic grommet, it aligns to a drilled circular bore rather than a routed slot. This works well on desks, counters, and other flat work surfaces where a standard hole saw or boring bit is used.
The pivot hinge hole for wire is built into the cap. During fitting, the cap can be oriented so the hinged opening faces the cable run, which helps direct wires naturally toward equipment without sharp bends at the exit point.
The 6650-014 manufacturer part number identifies this specific 3-1/4 inch black version within the larger 6650 series, which helps keep sizing and color consistent when repeating installations across several locations.
The Hardware Concepts, Inc. 6650 3-1/4 inch 2-piece cable grommet is placed in a 3-1/4 inch bore hole through desks, counters, or cabinet panels. That location gives a dedicated pass-through point where cables move from one side of the panel to the other.
As a round plastic cable grommet in black, it fits multimedia and workspace components where wiring needs to pass through a panel but the surface still needs to look finished. In shelf, closet, and garage organization layouts, the grommet can define a fixed opening, directing cords from mounted devices toward power or network locations.
The two-piece design with a separate hole liner lets the liner sit in the bore hole while the cap snaps or seats into it from above. This structure makes it practical to finish the hole after boring without additional edge treatments, because the liner shields the cut edge and the cap covers the top face.
The pivot hinge hole for wire in the cap provides an adjustable cable exit point. That pivoting section concentrates the wires into a single, shaped opening, which helps separate low-voltage lines from general clutter on the work surface when laying out equipment.
The 2-piece round plastic grommet uses a cap and hole liner so each function is split: the liner holds in the 3-1/4 inch bore and the cap handles the visible surface. This separation means wear from cables is taken by a replaceable plastic boundary, not the work surface itself.
Because the cap has a pivot hinge hole for wire, it can be set over cables already routed through the liner and then rotated. That pivot lets the opening align with the cable path, reducing side pressure on the wire insulation as equipment positions are adjusted.
The availability of eleven different sizes from 3/4 inch bore hole diameter to 3-1/2 inch bore hole diameter means the same 6650 style can be applied across small device leads up through larger cable bundles. This simplifies layout standards, because installers can base drill sizes on expected cable counts yet keep a consistent grommet look.
Seven color choices in this style grommet allow the visible cap and liner edge to coordinate with different finishes across a project. In practice, that lets a shop use one Hardware Concepts, Inc. 6650 family while matching oak-toned desks, white closet shelving, or dark garage work surfaces simply by varying color, not changing the basic hardware concept.
The 6650 3-1/4 inch 2-piece cable grommet is designed for a 3-1/4 inch bore hole diameter, so boring to that size lets the liner seat correctly and the cap match the opening.
The cap has a pivot hinge hole for wire that swings open, so cables can route through a defined opening while the cap stays in place, which helps direct wiring neatly.
This style grommet has two pieces, grommet cap and hole liner, so the liner fits the bore and the cap finishes the opening, protecting edges around the cable path.
The 6650 3-1/4 inch 2-piece cable grommet is used in multimedia and workspace components, desks, and organization systems where wires pass through panels.
Manufacturer part 6650-014 designates this black 3-1/4 inch version within the 6650 series, which helps match color and bore size across multiple installations.
These grommets are available in eleven different sizes from 3/4 inch to 3-1/2 inch bore and in seven colors, so layouts can keep the same style across variations.
The Hardware Concepts, Inc. 6650 3-1/4 inch 2-piece cable grommet in black combines a cap, a hole liner, and a pivot hinge hole for wire, giving a defined 3-1/4 inch bore interface that suits multimedia and workspace components needing clean cable transitions.
Sold In: 1 Each