1 inch grommet cap and liner set describes a two-piece Doug Mockett and Company, Inc. grommet assembly designed for a 3/4 inch bore hole, so it finishes a standard drilled opening with a matched cap and liner. The cap has a permanent cut out for wires, which gives cables a defined exit path and keeps them from rubbing directly against the hole edge. The white finish ties into light-colored desks, shelves, or cabinets, so the wire pass-through visually blends into the surface. The liner fits into the 3/4 inch bore hole, so the drilled opening is covered by a formed ring rather than raw material. Together, the cap and liner set organize the wire opening on multimedia and workspace components, so the feed-through looks intentional instead of improvised.
The AG3-95 designation identifies this grommet and cap, so installers can match the part to layouts that call for that specific style. The set is described as 1 inch grommet cap and liner set for 3/4 inch hole, so the liner is intended for a 3/4 inch bore. Using a 3/4 inch bore hole ties the drilled opening directly to the stated size, which simplifies layout when coordinating hole-drilling operations with wire routing. The cap and liner work together on shelf, closet, and garage organization components, so the same drilling pattern can carry through storage, workbench, and desk surfaces. Being part of multimedia and workspace components means the opening is sized with cable pass-through in mind, so power and data lines have a defined path through the panel.
This style grommet is listed under shelf, closet and garage organization, so it fits projects where wires must pass through storage or support panels without leaving a rough opening. Its multimedia and workspace components classification connects it directly to desks and workstations, so the 3/4 inch bore hole becomes a controlled path for cords at the back of a top or side panel. The white color supports use on light laminate or painted surfaces, so the wire exit point does not distract from the rest of the installation. Because the cap and liner work as a matched set, the visible portion of the opening stays consistent from one panel to the next, which helps when repeating the same wire routing pattern across several cabinets or workbenches.
This style grommet has two pieces, grommet cap and hole liner, so installers can treat the 3/4 inch bore as a controlled interface rather than a raw edge. The liner protects the edge of the bore, which helps maintain the integrity of the drilled hole when wires are threaded through or repositioned. The cap has a permanent cut out for wires, so cords always exit at the same point and angle, simplifying equipment placement relative to the pass-through. Identifying the set as 1 inch grommet cap and liner set for 3/4 inch hole, white, ties its physical size and color to a repeatable specification, which supports standardized layouts. Locating the part under grommets in multimedia and workspace components groups it with other wire management elements, so it can be selected as part of a coordinated cable-routing plan.
The AG3-95 grommet is described as a 1 inch grommet cap and liner set for a 3/4 inch hole, so it is intended for installations using a 3/4 inch bore.
This style grommet has two pieces, grommet cap and hole liner, so the liner fits into the 3/4 inch bore while the cap seats over it to finish the wire opening.
The cap has a permanent cut out for wires, so cables pass through a defined opening rather than over a raw edge, helping organize the exit point on the surface.
The grommet is listed under multimedia and workspace components and shelf, closet and garage organization, so it suits desks, workstations, and storage panels needing cable pass-through.
Doug Mockett and Company, Inc. uses AG3-95 as the manufacturer part number, so it identifies this specific white grommet cap and liner style for reordering or matching layouts.
The product is described as white, so it visually aligns with light-colored desks, shelves, and cabinets where a discreet-looking wire pass-through point is desired.
The 1 inch grommet cap and liner set for 3/4 inch hole, white, gives a defined solution wherever wires pass through panels on multimedia and workspace components. The AG3-95 two-piece design from Doug Mockett and Company, Inc. fits a 3/4 inch bore, so it aligns with common drilling setups in shop and onsite work. By using the matching white cap and liner around each opening, desks, storage panels, and workbenches share the same finished look at every cable pass-through point. For projects that call for a white wire exit in a 3/4 inch bore hole, this grommet configuration keeps the layout consistent from station to station.
Sold In: 10 Set
