3-1/2" Grommet Cap and Liner Set for 3" Hole, Putty

3-1/2 Grommet Cap And Liner Set Purpose

3-1/2 grommet cap and liner set describes a two-piece grommet designed to finish a 3 inch hole while controlling wire pass-through. The grommet cap and hole liner work together to clean up the bore edge and guide cables, which helps keep work surfaces organized and reduces snag points around the opening. The cap has a permanent cut out for wires, so cords always exit through a defined opening rather than an open hole, supporting consistent routing on desks, counters, or workstations. This style grommet is part of Doug Mockett and Company, Inc. multimedia and workspace components, positioning it for use anywhere wires pass through a horizontal surface. The putty color aligns with neutral worktop finishes, allowing the grommet to visually blend into many laminate or painted surfaces while still marking a clear pass-through point.

Key Details Of This Putty Wire Grommet

• This style grommet has two pieces; grommet cap and hole liner, so the liner shields the full 3 inch bore while the cap finishes the visible surface and cable exit.
• The cap has permanent cut out for wires, providing a dedicated opening that keeps cords grouped and helps limit lateral movement across the work surface.
• The set is sized as a 3-1/2 inch grommet cap and liner set for 3 inch hole, matching common drilled workstation and countertop feed-through openings.
• The product is identified as SAP Description GROMMET+CAP, PUTTY, giving a neutral putty tone that suits many office, closet, and workstation color schemes.
• The grommet belongs to multimedia and workspace components, so it supports cable routing for electronics, equipment, and other wired devices through horizontal panels.

Installation Fit Around The 3 Inch Bore Hole

The 3-1/2 inch grommet cap and liner set for 3 inch hole is sized to drop into a 3 inch bore hole, aligning with standard hole saw cuts in desks and panels. The hole liner nests inside the bore, covering the raw edge created by drilling, which helps protect cables from direct contact with the panel material. The grommet cap then seats over the liner, so the visible flange hides slight hole irregularities while the permanent wire cut out governs where cables exit. This style grommet is part of a family available in eight sizes from 3/4 inch bore hole diameter to 4 inch bore hole diameter, allowing consistent appearance across different cable pass-through sizes in the same project when matching other openings.

Using This XG3-93 Grommet In Work Surfaces

Where This Putty Grommet Cap Set Fits Best

The 3-1/2 inch grommet cap and liner set for 3 inch hole fits applications that need a finished opening for cable routing in shelves, closets, garage organization, and multimedia or workspace components. In closet or shelf layouts, the hole liner protects the cutout where power or low-voltage lines pass between compartments, while the cap keeps the opening visually clean. On desks or workstation counters, the permanent cut out for wires directs cords through a predictable exit point, helping keep laptops, monitors, and equipment cables grouped instead of spreading across the surface. Within garage organization, the grommet manages leads to chargers or tools by giving a defined feed-through location wherever a 3 inch bore hole is present. The neutral putty color helps the opening read as a simple functional detail within these environments, supporting a tidy appearance without drawing extra attention.

Why The Two-Piece Design Supports Clean Results

This style grommet has two pieces; grommet cap and hole liner, and the division directly affects installation quality. The liner surrounds the wall of the 3 inch bore hole, providing a smooth interface where cables contact the opening rather than leaving them against raw panel material. That liner also defines the internal diameter, so the cap can seat reliably and sit flush against the surface, even when the drilled hole shows minor tear-out. The cap has permanent cut out for wires, which locks in a fixed cable exit path, helping maintain consistent layouts when repeating the same hole position across multiple stations. Because this style grommet is grouped under multimedia and workspace components, it aligns with layouts that consolidate device cabling through controlled openings, supporting easier moves or changes around those fixed feed-through points. Being one of eight sizes from 3/4 inch bore hole diameter to 4 inch bore hole diameter, it fits into size-specific planning where different equipment clusters pass through appropriately scaled openings yet share the same Doug Mockett and Company, Inc. design language.

Common Questions About The XG3-93 Putty Grommet

Selecting This Putty Grommet For Your Openings

The 3-1/2 grommet cap and liner set for 3 inch hole in putty from Doug Mockett and Company, Inc. gives a defined way to finish cable openings in worktops, closets, or garage organization runs. Its two-piece style grommet design with grommet cap and hole liner supports both a clean edge at the bore and a controlled wire exit through the permanent cut out. For projects that already rely on multimedia and workspace components from the same family, choosing this XG3-93 grommet keeps the visual and functional approach consistent wherever a 3 inch wire pass-through is required.