3" Grommet Cap and Liner Set for 2-1/2" Hole, Polished Chrome

3 Inch Grommet Cap And Liner For Clean Cable Runs

3 inch grommet cap and liner give a finished, polished chrome pass-through point wherever a 2-1/2 inch hole is bored, so cables drop through cleanly instead of dragging across raw wood or laminate edges. This style grommet uses a two-piece design with a grommet cap and a matching hole liner, so the bore edge is covered all the way around for a neat, uniform appearance. The cap has a permanent cut out for wires, keeping cords in a defined channel rather than spreading across the surface. The grommet belongs to the multimedia and workspace components class, so it suits desks, counters, and similar work areas where organization and access for wiring are needed. The polished chrome finish gives a bright, metal look that pairs with chrome-finished hardware, helping work surfaces read as one coordinated installation.

Key Grommet Details That Support Clean Installs

• The 3 inch grommet cap and liner are sized for a 2-1/2 inch hole, so a standard bore quickly turns into a clean pass-through point without resizing or reshaping the opening on site.
• The two-piece style with separate cap and hole liner covers both the top surface and the bore wall, so the cut edge is hidden and protected for a more professional finish around wiring.
• The cap has a permanent cut out for wires, so cords follow a defined route through the opening, which reduces clutter across the surface and helps position cables where they are needed.
• The grommet is part of a line offered in eight sizes from 3/4 inch bore hole diameter to 4 inch bore hole diameter, so it aligns with other openings across the same project when matching components are selected.
• The polished chrome finish visually matches chrome-finished components in multimedia and workspace builds, so the pass-through point reads as an intentional detail instead of a rough field modification.

Installation Fit For 2-1/2 Inch Bored Openings

The grommet cap and liner are specified for a 2-1/2 inch bore hole diameter, so installers can drill that opening size and then drop the liner into the cutout as the interface between the surface and the wiring. The liner occupies the bore while the cap finishes the top face, so the two-piece setup simplifies aligning the visible edge with the cut hole. Because this style grommet is built as a matched cap and liner set, the parts are dimensioned to work together around the 2-1/2 inch opening, which helps the cap seat properly over the liner for a consistent reveal.

Using This Polished Chrome Grommet In Workspaces

Where This 3 Inch Chrome Grommet Works Best

The grommet belongs to the multimedia and workspace components category, so it is aimed at surfaces that carry power, data, or AV lines such as desks, workstations, and counters. The 3 inch grommet cap and liner set pairs with a 2-1/2 inch bore hole diameter, which suits typical cable bundles for computer equipment, small office gear, and similar setups that pass several cords through a single opening. The polished chrome finish ties into chrome details in shelf, closet, and garage organization layouts, so builders can carry the same visual language onto horizontal tops where cables exit. The permanent cut out in the cap keeps wires moving through a single opening rather than multiple field-drilled notches, supporting a consistent look across a run of work surfaces.

Why The Two-Piece Grommet Design Supports Repeatable Results

This style grommet uses two pieces - a grommet cap and hole liner - so installers work with a defined system instead of trimming raw edges around cords. The liner drops into the 2-1/2 inch bore hole diameter, establishing a stable collar that hides the cut edge, while the cap sits over the liner to finish the visible surface. That separation of liner and cap helps repeat the same appearance on multiple stations because each 2-1/2 inch opening receives the same sized liner and matching cap. The permanent cut out for wires in the cap eliminates decisions about where to notch the rim on site, which reduces variation from one opening to the next. With the grommet offered as part of a series spanning eight sizes from 3/4 inch to 4 inch bore hole diameters, planners can use the same basic design language when specifying different opening sizes across a project.

Common Questions About The EDP5-26 Chrome Grommet

Select This Chrome Grommet For 2-1/2 Inch Bores

The 3 inch grommet cap and liner set for a 2-1/2 inch hole in polished chrome offers a defined, wire-ready opening wherever a clean pass-through is needed on desks or work surfaces. With its two-piece construction and permanent wire cut out in the cap, the grommet turns a standard bore into an organized routing point sized to the opening. For projects built around multimedia and workspace components from Wurth Baer Supply, this EDP5-26 polished chrome grommet gives an identified solution when planning cable routes through horizontal surfaces.