2" Grommet Set for 1-3/4" Hole, Putty
Description
2 Grommet Set For 1-3/4 Hole Putty Wire Management
2 grommet set for 1-3/4 hole putty describes a two-piece Doug Mockett and Company, Inc. SG3-93 grommet assembly that manages wires passing through a work surface, so cables route cleanly through a 1-3/4 inch bore instead of running across the top. This style grommet has two pieces; grommet cap and hole liner, so the raw bore edge is shielded by the liner while the cap organizes the wire exit point for a finished feed-through. The cap has permanent cut out for wires, which keeps an always-open wire path and removes the step of punching knockouts during installation. The 2 inch set is part of a family available in eight sizes from 3/4 inch bore hole diameter to 4 inch bore hole diameter, which helps standardize the look across different openings on the same project. The grommet belongs to the multimedia and workspace components category, aligning it with desks, counters, and similar work surfaces where cable pass-through is required.
Key Grommet Details That Support Clean Installs
- This style grommet has two pieces; grommet cap and hole liner, so the bore edge is concealed by the liner while the cap defines the visible opening, giving a neater appearance at the work surface.
- The cap has permanent cut out for wires, allowing cables to pass through without modification, which speeds installation and reduces handling on each opening.
- The set is sized as a 2 inch grommet for a 1-3/4 inch bore hole, so the liner nests into a standard drilled opening while the cap slightly overhangs for a clean trim ring effect.
- The grommet is part of a range available in eight sizes from 3/4 inch bore hole diameter to 4 inch bore hole diameter, allowing the same style to be used across small electronics leads and larger cable bundles.
- The product sits in the multimedia and workspace components class under grommets, aligning it with desk, counter, and workstation layouts where organized wire routing supports tidy, usable surfaces.
Grommet Fit Around A 1-3/4 Inch Bore Hole
The 2 inch grommet set for 1-3/4 inch hole is sized so the hole liner fills a 1-3/4 inch bore, letting installers drill a consistent diameter while relying on the liner for the finished edge. The 2 inch cap then conceals slight bore variations around the top, giving some visual forgiveness where bits may wander or materials chip. The permanent cut out for wires in the cap establishes a fixed cable exit, so routing stays predictable on repeated workstation layouts. Being a grommet in the shelf, closet, and garage organization category ties it to projects where cables must pass through panels or shelving without exposing raw edges to users or wires.
Using This Doug Mockett SG3-93 Grommet Set In Projects
Where This Putty Grommet Set Fits Best
The Doug Mockett and Company, Inc. SG3-93 grommet and cap, putty 1-3/4 bore, fits work surfaces, shelves, or closet panels that need a 1-3/4 inch bore to carry wiring between spaces. As a multimedia and workspace component, it suits desks, counters, and similar layouts where devices on top connect to power or data below through a tidy opening. Its place in shelf, closet, and garage organization means it also supports organized routing through vertical panels, so cables transition between compartments while the hole liner protects the cut edge. The 2 inch description signals the visible cap footprint around the 1-3/4 inch bore, so the opening looks proportionate on common panel dimensions used in cabinetry and workstations.
Why This Two-Piece Grommet Helps Repeatable Results
This style grommet has two pieces; grommet cap and hole liner, which separates the drilling step from the finishing step, letting installers drill the 1-3/4 inch bore independently and then snap the liner and cap into place for a consistent appearance. The cap has permanent cut out for wires, so every opening in a run behaves the same way, with cables exiting through the same styled cutout without extra prep. Being available in eight sizes from 3/4 inch bore hole diameter to 4 inch bore hole diameter lets a shop keep the same look and assembly approach while changing only the bore size, which supports standardized tooling. The SG3-93 part marking identifies this specific putty 1-3/4 bore version in that family, simplifying repeat ordering when a project spec calls out this combination of cap, liner, and bore size.
Common Questions About The SG3-93 Grommet Set
What opening size does the SG3-93 grommet set work with?
The SG3-93 grommet set is described as a 2 inch grommet for a 1-3/4 inch bore hole, so the drilled opening is 1-3/4 inch while the cap covers slightly beyond the edge.
How do the grommet cap and hole liner function together?
This style grommet has two pieces; grommet cap and hole liner, so the liner fits into the bore and the cap finishes the top surface, protecting the hole edge and shaping the wire exit.
What does the permanent cut out for wires provide?
The cap has permanent cut out for wires, creating a fixed opening for cables so wires pass through without alteration, which supports consistent cable routing on multiple openings.
Where is this SG3-93 grommet typically used?
The SG3-93 is listed under multimedia and workspace components and shelf, closet, and garage organization, aligning it with desks, counters, shelves, and panels that route wiring through a bore hole.
How does this size relate to other grommets in the range?
This 2 inch grommet set for a 1-3/4 inch bore is one of a series available in eight sizes from 3/4 inch bore hole diameter to 4 inch bore hole diameter, supporting consistent styling across various openings.
What does the SG3-93 part number identify?
Manufacturer part SG3-93 identifies this Doug Mockett and Company, Inc. grommet and cap, putty 1-3/4 bore, so reordering the same finish and size is straightforward when matching existing installs.
Select This SG3-93 Grommet Set For Clean Wire Runs
The 2 grommet set for 1-3/4 hole putty from Doug Mockett and Company, Inc. combines a grommet cap and hole liner to turn a simple 1-3/4 inch bore into a finished, cable-ready pass-through. Its permanent cut out for wires keeps routing straightforward across desks, shelves, and workspace panels. The SG3-93 part belongs to a family spanning eight bore sizes from 3/4 inch to 4 inch, so this specific putty 1-3/4 bore option fits projects that standardize on that opening size while matching existing Mockett styling.
