Round Wire Grommets For Clean Wire Pass-Through

Round Wire Grommets give a two piece plastic solution for routing wires through work surfaces, helping organize multimedia and workspace components in a clean, finished way. This Doug Mockett and Company, Inc. TG5-26 (5SET/BAG) style uses a grommet cap paired with a hole liner, so the bore hole edge is covered while wires pass through a defined opening. The grommet series is available in eight sizes from 3/4 inch bore hole diameter to 4 inch bore hole diameter, which supports a range of hole sizes across desks, cabinets, and panels using the same visual family. The cap has a permanent cut out for wires, keeping the opening consistent so cables sit in a fixed path instead of shifting against the laminate or wood edge. The SAP description specifies chrome plated, giving the visible cap a metallic look that matches chrome-oriented hardware runs.

Key Chrome Plated Wire Grommet Advantages

• The two piece plastic design with grommet cap and hole liner covers the raw bore hole edge, so wires contact a smoother plastic surface instead of the panel edge during routing.
• The cap has a permanent cut out for wires, which maintains a fixed cable path and helps keep cords grouped as they exit work surfaces or cabinetry.
• Availability in eight sizes from 3/4 inch to 4 inch bore hole diameter lets one grommet style visually align across different openings in the same installation.
• The chrome plated description on the grommet and cap provides a metallic appearance that ties into chrome-finished hardware and trim in office or cabinet layouts.
• The product is sold in full box quantities only, supporting repeat use across multiple cabinets, desks, or panels on the same project.

Wire Grommet Bore Hole And Fit Details

This Round Wire Grommets line is defined by bore hole sizing from 3/4 inch to 4 inch diameter, so each opening is matched by a corresponding grommet size for a snug, finished fit. The design uses a grommet cap with a dedicated hole liner, so the panel bore receives a liner ring while the cap finishes the surface interface. Because the cap’s permanent cut out is formed as part of the cap, the finished diameter and cable path stay consistent for each chosen size. The product class is listed as Grommets under multimedia and workspace components, aligning it with typical desk, cabinet, and equipment panel applications where through-holes are pre-bored to the specified diameters.

Using TG5-26 Grommets In Workspace Projects

Where This Two Piece Plastic Grommet Fits Best

The Round Wire Grommets product name places this TG5-26 grommet in the Round Wire Grommets family, so it is intended for routed or drilled round openings rather than slots or irregular shapes. With bore hole sizing that spans from 3/4 inch to 4 inch diameter across the line, these grommets address small cable pass-throughs up to larger bundles in desktops, workstations, cabinetry, and closet or garage organization panels. Category placement under Shelf, Closet & Garage Organization and Multimedia and Workspace Components shows its role in projects that combine storage with powered equipment, where wires need a defined exit point. The two piece plastic structure, described as grommet cap and hole liner, positions the liner inside the bore hole while the cap finishes the outer face, so both sides of the opening present a controlled plastic interface around the cable group.

Why TG5-26 Details Support Consistent Results

The web description specifies that the cap has a permanent cut out for wires, so the opening is not adjusted after installation and cable paths remain repeatable from station to station. This fixed geometry helps maintain uniform exit points when multiple work surfaces are processed with the same TG5-26 pattern. The chrome plated wording in the SAP description gives the cap and liner a chrome-look surface, which can visually coordinate with chrome-finished pulls, brackets, or frame components in the same installation. Because the TG5-26 (5SET/BAG) designation and product name tie this item to Doug Mockett and Company, Inc., buyers can align it with other Doug Mockett components specified on drawings. The note that it is sold in full box quantities only helps plan quantities for multi-station jobs, since each box is structured for repetitive use across several panels or cabinets.

Common TG5-26 Wire Grommet Buyer Questions

Select TG5-26 Grommets For Coordinated Wire Runs

The Round Wire Grommets TG5-26 (5SET/BAG) style from Doug Mockett and Company, Inc. combines a grommet cap, hole liner, and chrome plated appearance to finish round wire pass-throughs. With sizes across 3/4 inch to 4 inch bore hole diameters and a permanent wire cut out in the cap, this two piece plastic design supports consistent, repeatable cable exits on work surfaces and cabinetry. Sold in full box quantities only, it aligns well with projects that standardize openings across multiple panels. Select this TG5-26 configuration when a chrome-look Round Wire Grommets solution is specified for multimedia and workspace components.