36" KV255 Heavy-Duty Aluminum Pilaster Standard, Natural Aluminum Finish 100/Box

KV255 Heavy-Duty Pilaster Standard For Adjustable Shelves

KV255 heavy-duty pilaster standard describes a Knape and Vogt aluminum shelf standard designed for adjustable shelving layouts in cabinet, closet, or storage builds. This 36 inch 255AL 36 standard is part of the KV255 model family, so it follows a consistent geometry when you are planning multiple runs or tying into existing work that already uses the KV255 pattern. The standard measures 5/8 inch wide by 3/16 inch deep, which helps it sit neatly in narrow stiles or shallow casework while still giving defined support engagement. Slots for supports are adjustable in 1/2 inch increments, which lets you fine-tune shelf elevation without large jumps and match heights between adjoining units. Stamped numbers on the standard simplify layout, because you can repeat shelf positions accurately across several openings. The natural aluminum finish suits projects calling for a clean metallic look that visually matches other natural aluminum components.

Key Shelf Standard Details That Help On Site

• The 36 inch length supports mid-height cabinets or closet sections, so you can span common opening heights without trimming and keep shelf positions consistent.
• The standard belongs to the KV255 model series, helping you coordinate with other KV255 lengths and maintain the same bracket and slot interface across a project.
• The 5/8 inch width gives a slim profile that fits in narrow face frames or panel sides while still providing a defined bearing surface for shelf supports.
• The 3/16 inch depth keeps the standard shallow, which is useful where carcass material is limited and you want capacity without overcutting grooves.
• Slots adjustable in 1/2 inch increments allow closer shelf spacing control, so you can set heights for specific stored items instead of living with coarse steps.
• Stamped numbers along the standard aid repeatable layout, letting you match shelf levels left-to-right and between cabinets without constant tape measurements.
• The natural aluminum finish presents a neutral metallic appearance that coordinates with typical natural aluminum hardware for a uniform interior look.

Installation And Fastener Pattern For KV255 Standards

This 36 inch aluminum standard uses pre-drilled screw or nail holes 6 inches apart on center, giving an even fastening pattern from top to bottom. That spacing helps distribute load into the cabinet or wall substrate without guesswork about where to place fasteners. The material is 17-gauge aluminum, so you are working with a standard that is built for strength in an aluminum profile while still being workable during install or adjustment. Recommended fasteners are KV255-8 nails, sold separately, which ties the standard to a specific nail option when you are planning material lists. The standard is BHMA Grade 1 compliant, so it meets a recognized performance classification for shelf standards, which matters on projects where graded hardware is expected or specified.

Where This 36 Inch KV255 Standard Fits Best

Natural Aluminum KV255 Standard In Cabinet Runs

This Knape and Vogt KV255 heavy-duty aluminum pilaster standard is 36 inches long, which suits base cabinets, closet sections, or storage bays where you need adjustable shelving within that height range. Because the standard is 5/8 inch wide by 3/16 inch deep, it integrates well into side panels or face-frame stiles without demanding excessive routing depth, which helps preserve material strength around the groove. The BHMA Grade 1 compliant designation supports use in demanding environments where frequent shelf adjustment and higher loading are normal. Natural aluminum finish means the standard visually coordinates with other natural aluminum hardware in the space, so interior views through open doors remain consistent.

Details That Support Repeatable Shelf Layout And Replacement

The KV255 model identity ties directly to a family of standards with matching slot geometry, which simplifies both new layouts and replacements, because the same bracket interface applies across the range of listed lengths. Aluminum standards in this series use 17-gauge aluminum, giving a durable profile that holds slot shape under typical shelving loads. Slots for supports are adjustable in 1/2 inch increments, which lets you align shelves with scribed lines, adjoining cases, or known appliance heights while keeping measurements straightforward. Stamped numbers along the run turn those increments into quick reference points, so you can reproduce the same shelf position on multiple standards without re-measuring each location. Pre-drilled screw or nail holes 6 inches apart on center provide a consistent fastening grid from top to bottom, distributing forces into the cabinet side or wall structure. This even pattern helps the standard stay seated flat, supporting accurate bracket engagement over the full height of the installation.

Common Questions About The 255AL 36 KV255 Standard

Selecting This KV255 Standard For Your Next Run

The 36 inch KV255 heavy-duty pilaster standard in natural aluminum brings BHMA Grade 1 compliant performance, 5/8 inch by 3/16 inch sizing, and 1/2 inch shelf adjustments into one consistent profile. When your project calls for a 17-gauge aluminum standard with pre-drilled 6 inch on-center fastener holes and stamped measurement numbers, this 255AL 36 part number from Knape and Vogt gives you a defined, repeatable pattern for adjustable shelving work.