Order by 24/7 by web, contact our sales reps or call by phone.
What you need, when you need it, all in one place.
Most orders ship same day.
Advice and support from knowledgeable professionals.
36 inch KV255 steel pilaster standard is a Knape and Vogt vertical shelf standard designed to support adjustable shelving runs in cabinets, closets, and storage applications. The KV255 model identity ties this standard directly to matching Knape and Vogt components, which matters when a project calls for consistent hardware across multiple openings. The 36 inch length works well for mid-height cabinets or closet sections where several shelf positions are needed without running floor to ceiling. Steel construction means the standard is built around a rigid backbone, so it supports heavier stored items when matched with appropriate brackets. The zinc finish coats the steel surface, which matters in busy storage areas because it helps resist everyday wear at the slot edges. As part of the Shelf Standards and Brackets category, this piece serves as the structural track that lets installers fine-tune shelf elevation after the casework is in place.
The KV255 pilaster standard uses pre-drilled screw or nail holes every 6 inches on center, so fastener placement follows a consistent pattern that supports predictable load transfer into cabinet sides or wall framing. With 5/8 inch width and 3/16 inch depth, the standard presents a slim profile that sits close to the mounting surface, which helps brackets seat properly without pushing shelves far from the wall. Slots arranged in 1/2 inch increments create a dense adjustment grid, so installers can adjust shelf height by small steps to match design lines or clear obstructions. The product description notes KV255-8 nails as recommended fasteners, giving a clear reference when choosing nail type for installations that favor nail-driven attachment.
This 36 inch Knape and Vogt shelf standard fits applications where mid-height storage is needed, such as wall cabinets, tall base cabinets, or closet sections that do not extend full height. The length gives enough vertical run for multiple shelf positions without overextending into unused space. Being part of the Shelf, Closet and Garage Organization category, the standard suits projects where adjustable storage is expected, such as garage organizing runs, pantry shelving, or utility cabinets. The zinc finish provides a neutral metallic look that pairs with a range of bracket finishes within the available zinc option, helping installations maintain a consistent appearance. Because the standard follows the KV255 model structure, it aligns with the broader KV255 system, which matters when multiple openings must share the same adjustment geometry across a project.
The slots on the KV255 standard are spaced in 1/2 inch increments, creating a fine adjustment pattern that lets installers raise or lower shelves in small, predictable steps, which is helpful when matching trim lines or appliance clearances. Stamped numbers along the standard give each slot position a visible reference, simplifying layout when setting multiple shelves to the same height in different cabinets, since the installer can match slot numbers instead of remeasuring. Pre-drilled holes every 6 inches on center provide a regular fastening rhythm that helps keep the standard straight during installation, supporting accurate bracket engagement. The 23-gauge high strength steel construction keeps deflection low at the slots and hook points under load, which helps shelves maintain alignment over time when paired with appropriately rated brackets. Together, these characteristics allow a repeatable workflow for adjusting or reconfiguring shelf layouts as storage needs change.
The product is a 36 inch KV255 pilaster standard, which suits mid-height cabinet or closet sections where several shelf positions are needed without running floor to ceiling.
The 255 ZC 36 standard is made from 23-gauge high strength steel, providing a rigid track for shelf brackets so loaded shelves stay supported within typical storage applications.
The standard is 5/8 inch wide and 3/16 inch deep, giving a slim profile that fits neatly along cabinet sides while keeping shelves close to the wall.
The KV255 pilaster has slots set in 1/2 inch increments, so shelf brackets can be moved up or down in small steps to fine-tune storage height or align with adjacent surfaces.
This standard has pre-drilled screw or nail holes 6 inches on center, creating a regular fastening pattern that helps distribute loads along the mounting surface.
The description lists KV255-8 nails as recommended fasteners, giving a direct reference when choosing nail type for installations suited to nail-driven attachment.
This 36 inch KV255 heavy-duty steel pilaster standard with zinc finish provides a defined length, material, and adjustment pattern for adjustable shelving projects. With 23-gauge high strength steel, 5/8 inch width, 3/16 inch depth, and 1/2 inch slot increments, it establishes a predictable framework for shelf layout. The BHMA Grade 1 compliance noted in the description signals a standard built around demanding performance criteria, which matters when planning storage that must carry significant daily use. For projects matching these dimensions and finish, this Knape and Vogt 255 ZC 36 standard offers a clear, repeatable basis for building adjustable shelving runs.
Sold In: 1 Each
