18" KV255 Heavy-Duty Steel Pilaster Standard, Almond Finish 100/Box

KV255 Heavy-Duty Steel Pilaster Standard Use

KV255 heavy-duty steel pilaster standard describes an 18 inch Knape and Vogt shelf standard that carries the KV255 model designation, so it matches projects already laid out around this system. The standard is 5/8 inch wide and 3/16 inch deep, giving a slim profile that sits close to the cabinet or closet side panel while still providing support. The material is 23-gauge high strength steel in this steel version, which supports demanding shelving layouts in closets, cabinets, or storage runs. The almond finish identifies the color as almond, helping the standard blend with almond-toned interiors. Slots for supports are adjustable in 1/2 inch increments, allowing shelf locations to be stepped up or down in half-inch steps to fine-tune clearances around stored items. Stamped numbers are present along the standard, which gives a visual reference point that simplifies aligning opposing standards to the same shelf elevations.

Key Shelf Standard Details For Installers

• The Knape and Vogt KV255 model designation ties this 18 inch standard to the broader KV255 system, which helps keep components consistent across a job.
• The 5/8 inch width and 3/16 inch depth keep the pilaster low profile against the side panel, which preserves usable shelf width while still giving bracket engagement.
• Slots for supports adjustable in 1/2 inch increments let you set shelf heights in half-inch steps, which makes it easier to hit exact clearances over bins or hanging items.
• Stamped numbers along the standard provide clearly marked reference points, which speeds up layout and helps keep opposing standards level with each other.
• Pre-drilled screw or nail holes 6 inches apart on center provide regular fastening points, which supports a consistent fastening pattern along studs or cabinet sides.

Installation Layout And Fastening Details

The standard has pre-drilled screw or nail holes spaced 6 inches apart on center, so fastening points fall on a predictable grid during layout. This 18 inch length lets you cover shorter cabinet interiors or closet sections where a full-height run is not needed. The steel version uses 23-gauge high strength steel, which supports typical fastening with screws or nails through the pre-drilled holes into the substrate. Slots for supports are cut to adjust in 1/2 inch increments, so once the standards are fastened plumb, shelves can be moved up or down by half an inch at a time without reworking the installation.

Where This 18 Inch KV255 Standard Fits Work

Use In Shelf, Closet, And Storage Runs

The product is classified under Shelf, Closet and Garage Organization and Shelf Standards and Brackets, so it is oriented toward adjustable shelving layouts in those environments. The 18 inch length suits shorter cabinet bays or lower sections within a closet where full-height standards are unnecessary. The almond finish identifies the color as almond, matching almond-toned casework or complementing light-colored interiors. Because the standard width is 5/8 inch and depth is 3/16 inch, it occupies minimal side clearance, leaving more width for shelving while still engaging compatible supports in the slots. With slots adjustable in 1/2 inch increments, this standard supports storage layouts where small vertical adjustments help fit containers, folded items, or equipment into tight spaces.

Details That Support Accurate Replacement And Layout

The manufacturer part number 255 ALM 18 clearly identifies this piece as a KV255 almond finish standard in an 18 inch length, which matters when matching existing installations that already use KV255 components. Stamped numbers running the length of the standard give a repeatable reference when setting multiple standards, which helps align shelf brackets at the same level across a bank of cabinets or along a closet wall. Pre-drilled screw or nail holes spaced 6 inches on center provide a consistent pattern that simplifies transferring hole locations to cabinet sides or wall studs. The 23-gauge high strength steel construction gives the standard rigidity appropriate to a heavy-duty classification within the KV255 line, which supports repeated shelf repositioning in normal service. BHMA Grade 1 compliance is called out as a feature, tying the standard to a recognized performance grade for this category.

Common Questions About The KV255 Almond Standard

Selecting This KV255 Standard For Your Project

This 18 inch Knape and Vogt KV255 heavy-duty steel pilaster standard in almond finish pairs an 18 inch length with 5/8 inch width and 3/16 inch depth, fitting shorter cabinet or closet bays. Slots adjustable in 1/2 inch increments and stamped numbers support accurate, repeatable shelf layout. Pre-drilled screw or nail holes 6 inches on center streamline fastening into cabinet sides or wall framing. For projects built around the KV255 pattern, the 255 ALM 18 designation clearly identifies this almond 18 inch component so it matches the intended system.